Filter
Top Products
154
Appendix NAVI/AV
Route calculation was not possible. Route calculation has failed because
of a malfunction of map data, soft-
ware, hardware or disc.
• Change the destination.
• Clean the disc.
• Consult the Pioneer Local dealer if
this message persists.
Route calculation was not possible
because the destination is too far.
The destination is too far. •Set a destination closer to the start-
ing point.
• Set one or more way points.
Route calculation was not possible
because the destination is too near.
The destination or way point(s) are
too close.
Set a destination or way point(s) far-
ther from the starting point.
Route calculation was not possible
due to traffic regulations.
• The destination or way point(s) are
in a Control Traffic Zone (CTR) and
the route calculation is hampered.
• Your vehicle is currently in a Con-
trol Traffic Zone (CTR) and the
route calculation is hampered.
• Set a destination and way point(s)
outside the CTR if you know where
the restricted area is.
• Try a destination or way point(s)
away from the currently set points
to some extent.
• Drive your vehicle to an unre-
stricted area and reset the destina-
tion and way point(s).
Route calculation was not possible
because no guidance can be pro-
vided around the destination or the
starting point.
The destination, way point(s) or start-
ing point are in an area where no
road exists (e.g. a mountain) and the
route calculation is impossible.
• Set a destination and way point(s)
on roads.
• Reset the destination after you
drive the vehicle to any road.
There is no route to the destination. The destination or way point(s) are on
an isolated island, etc. without a ferry
and the route calculation is impossi-
ble.
Change the destination.
The route could not avoid the speci-
fied area.
If route setting cannot avoid speci-
fied Areas to Avoid.
If the current route is not desired, set
a destination or way point(s) that do
not pass through the Areas to
Avoid.
The route could not avoid the speci-
fied area.
Toll road has not been avoided.
If the route to the destination or way
point(s) cannot be established by
bypassing toll roads (including toll
areas) and Areas to Avoid.
If the current route is not desired, set
a destination or way point(s) that do
not pass through toll roads (includ-
ing toll areas) and Areas to Avoid.
Ferry has not been avoided. In case a ferry route was included in
the route to the destination or way
point(s) even though “Avoid Ferry”
was set to On.
If the current route is not desired, set
a destination or way point(s) that do
not pass through a ferry route.
Toll road has not been avoided. If the route to the destination or way
point(s) cannot be established by
bypassing toll roads (including toll
areas).
If the current route is not desired, set
a destination or way point(s) that do
not pass through toll roads (includ-
ing toll areas).
The address does not exist.
Do you want to continue?
If the house number is entered with-
out specifying city or street and that
house number does not exist on the
data.
Re-enter the existing house number
by following the instructions shown
on the screen.
Or, proceed to the next step without
entering the house number and
specify the city or street first.
There is no applicable data for the
selected city. Automatically returning
to list.
If the history data of the city could
not be used (for example, if the his-
tory data of the city that was used in
the POI Search cannot be found in
the Address Search.)
Once the search is performed to
specify the city, the result is saved as
a history. The data of the specified
city, however, may not be hit by the
different search criteria. In this case,
try another search method or change
the destination.
There is no Freeway in this area. If no freeway was found in the
selected Zone.
Set the destination or way points
using another search method or
change the location of the destina-
tion or way point(s).
Message When What to do