Filter
Top Products
Command ASCII command
(host to processor)
Response
(processor to host)
Additional description
Input Switching and Configuration
Input selection
Select input
X!! InX!] Select video from input X!.
View current input
!
X!]
View currently selected input source.
Input video format
Set format
EX!*X#ITYP
}
ITypX!*X#*X%] Set input X! to video format X#.
Detected format X% is also reported in
response
View format
EX!ITYP
}
X#*X%] View video format of input X!.
Detected format X% is also reported in
response
View input standard
EX!ISTD
}
(tagged response in verbose
mode 2/3)
X!*X1!]
ISTD X!*X1!]
View video standard X1! for input X!.
Verbose mode (2/3)
Input EDID
Specify an EDID value
EAX!*X2@EDID
}
EdidX!*X2@] Set EDID resolution and refresh X2@
for input X!.
View EDID value
EAX!EDID} X2@]
EdidAX!*X2@]
View EDID resolution and refresh X2@
for input X!.
Verbose mode (2/3)
Save an outputs EDID
ESX@*X2@EDID
}
EdidSX@*X2@] Set output X@ EDID to X2@.
(Valid for X2@ = 201, 202, 203 only,
and X@ = 1, 2 and 3 only.)
Export EDID file
EEX2@,EDID} X2$]
Exports EDID table X2$.
Import an EDID file
EIX2@,X2$EDID}
EdidIX2@] Imports user defined EDID to X2@
(valid for X2@ = 201, 202, 203 only).
Auto-Image
Enable auto image
X!*1A ImgX!*1] Enable Auto image for input X! (only
available for input 1).
Disable auto image
X!*0A ImgX!*0] Turn off auto image for input X! (only
available for input 1).
Execute auto image
A
Img0]
Execute auto image for current input.
Execute and Fill
1*A
Img1]
Execute auto image and fill entire
output.
Execute and Follow
2*A
Img2]
Execute auto image and follow the
input’s aspect ratio.
View auto image
X!A X1)] View auto image setting for input X!.
NOTE: X! = Input selection; 1 – 3
X@ = Output selection: 0 = All outputs (Only available for Video Mute), 1 = Output 1 Only (HDMI),
2 = Output 2A Only (HDMI), 3 = Output 2B Only (DTP)
X# = Input video format; 0 = Auto detect (default), 1 = RGB, 2 = Auto YUV, 3 = RGBcvS, 4 = S-video,
5 = Composite video, 6 = HDMI/DVI, 7 = DisplayPort
X% = Detected Input Video Format: 0 = No signal present, 1 = RGB, 2 = Auto YUV, 3 = RGBcvS, 4 = S-Video,
5 = Composite, 6 = DVI, 7 = HDMI, 8 = DisplayPort
X1)
= 0 (off/disable), 1 (on/enable)
X1! = Input standard: 0 = No signal, 1 = NTSC, 2 = PAL, 3 = SECAM, - = N/A (when input is set to a high
resolution signal format)
X2@ = EDID emulation: see page 36 for EDID resolution and refresh rates
X2$ = EDID Table; 128 or 256 Bytes.
Annotator 300 • SIS Communication and Control 41