Filter
Top Products
2 Figures
P0609324 01
Figure 41 Rear of GATM module, showing DIP switch locations . . . . . . . . . . . . . . . 94
Figure 42 Process map: Installing a media bay module . . . . . . . . . . . . . . . . . . . . . 107
Figure 43 Removing the front bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 44 Identifying the media bay module latches . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 45 Warning of possible shorting issue on media bay modules . . . . . . . . . . 110
Figure 46 Process map: Replacing a media bay module . . . . . . . . . . . . . . . . . . . . 112
Figure 47 LEDs confirm that BCM1000 is active . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Figure 48 Locating the data cards on the BCM1000 . . . . . . . . . . . . . . . . . . . . . . . 119
Figure 49 Serial pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Figure 50 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Figure 51 Ethernet crossover cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Figure 52 Process map: Trunk and station wiring process map . . . . . . . . . . . . . . . 132
Figure 53 DTM RJ48C wiring array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Figure 54 CTM RJ11 wiring array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Figure 55 GATM cable wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Figure 56 BRI RJ45 wiring array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Figure 57 Wiring for DSM 16, 4X16, and DSM 32 . . . . . . . . . . . . . . . . . . . . . . . . . 137
Figure 58 Wiring for an ASM 8 or ASM8+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Figure 59 Analog telephone installation overview . . . . . . . . . . . . . . . . . . . . . . . . . 151
Figure 60 Data communication device installation overview . . . . . . . . . . . . . . . . . 151
Figure 61 ATA 2 top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Figure 62 ATA 2 pin outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Figure 63 ATA 2 back view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Figure 64 Insertion loss from the CO to the analog telephone . . . . . . . . . . . . . . . . 154
Figure 65 Auxiliary ringer jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Figure 66 Audio input jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Figure 67 Page relay jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Figure 68 Music-on-hold jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Figure 69 SSM board connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 70 LED locations on the face of the BCM1000 . . . . . . . . . . . . . . . . . . . . . . 163
Figure 71 System Status Monitor LED Display screen . . . . . . . . . . . . . . . . . . . . . . 163
Figure 72 System Status Monitor LED Settings record . . . . . . . . . . . . . . . . . . . . . 164
Figure 73 Process Map: Preparing the units for maintenance . . . . . . . . . . . . . . . . 167
Figure 74 Remove the top cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Figure 75 Removing the front bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Figure 76 Process map: Hard disk replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Figure 77 Hard disk wiring (single disk) and screw locations (2.0 hardware) . . . . . 175
Figure 78 Hard disk and screw locations (2.5 version hardware) . . . . . . . . . . . . . . 175
Figure 79 Remove the brackets from the hard disk . . . . . . . . . . . . . . . . . . . . . . . . 176
Figure 80 Connect the brackets to the hard disk (single-disk system) . . . . . . . . . . 177
Figure 81 Installing two hard disks for a mirrored disk system . . . . . . . . . . . . . . . . 177
Figure 82 Cabling the RAID board to the hard disks . . . . . . . . . . . . . . . . . . . . . . . 178