Filter
Top Products
Command ASCII Command
(host to scaler)
Response
(scaler to host)
Additional Description
Video effect
Cut
E0SWEF
}
Swef0]
Sets the switch to cut.
Dissolve
E1SWEF} Swef1]
Sets the switch to dissolve.
View setting
ESWEF} 0] (or 1])
View setting (0 = cut, 1 = dissolve).
Effect duration
Set dissolve duration
EX3%EDUR
}
EDURX3%]
Sets the effect duration to tenths of seconds
(range 2 = 0.2 to 50 = 05.0 seconds. Default
is 3 = 0.3 seconds).
View duration
EEDUR}
X3%]
View effect duration.
Front panel security lockout (Executive Mode)
Enable Executive
mode 1
1X Exe1]
Lock entire front panel.
Enable Executive
mode 2
2X Exe2]
Limited front panel adjustments (input
selection, PIP/Swap, and Auto- Image) can
be made.
Disable Executive
mode
0X Exe0]
Unlock front panel controls. All front panel
adjustments can be made.
View Executive
mode status
X 0] (or) 1]
(or) 2]
View the current status:
0 = off [default]; 1 = on, complete;
2 = on, limited adjustments.
Overscan mode (applies only to SMPTE [NTSC, PAL, 480p, 576p, 720p, 1080i, 1080p] input rates)
Set value
EX#*X2*OSCN} OscnX#*X2*]
Set input format X# to overscan mode X2*.
View status
EX#OSCN}
X2*]
Show overscan mode status for input
format X#.
HDCP notification (green screen/message)
Enable notification
EN1HDCP} HdcpN1]
Enable the HDCP notification.
Disable notification
EN0HDCP} HdcpN0]
Disable the HDCP notification; instead
mute output.
Query notification
ENHDCP}
X(]
Query the HDCP notification.
HDCP status (valid for HDMI inputs and HDMI oututs only)
Query input
EIX!HDCP}
X3#]
HdcpIX!*X3#]
Query the HDCP status of the current input
X!.
Verbose mode response
Query output
EOX@HDCP}
X3#]
HdcpOX@*X3#]
Query the HDCP status of the HDMI output
X@.
Verbose mode response
NOTE: X! = Input selection: 1 to 5
X@ = Output selection: 0 = all outputs (default), 1 = analog (VGA, YUVp, HDTV), 2 = HDMI, 3 = 3G/HD-SDI, 4 = none
X# = Input video format: 0 = no signal detected, 1 = RGB, 2 = YUV auto, 3 = RGBcvS, 4 = S-video, 5 = composite,
6 = DVI/HDMI (only available for inputs 3, 4, and 5), 7 = Autodetect (default for inputs 1 and 2)
X( = Enable/disable: 0 = off/disable, 1 = on/enable
X2* = Overscan (applied to SMPTE [NTSC/PAL - 480p -1080p] input rates), 0 = 0.0% (default for RGB/HDMI),
1 = 2.5% (default for YUV, RGBcvS, S-video composite). See X2* on page 37 for details.
X3# = HDCP status (valid only on HDMI/DVI outputs): 0 = no sink or source detected, 1 = sink or source detected with HDCP,
2 = sink or source detected but no HDCP is present
X3% = Effect duration: from 2 to 50, in 0.1 second steps (where 2 = 0.2 seconds, 50 = 5.0 seconds), default = 3 (0.3 seconds)
DVS 605 • SIS Communication and Control 52