Command ASCII Command
(host to scaler)
Response
(scaler to host)
Additional Description
Front panel security lockout (Executive Mode)
Enable Executive
mode 1
1X Exe1]
Lock entire front panel.
Enable Executive
mode 2
2X Exe2]
Limited front panel adjustments (input
selection, PIP/Swap, and Auto- Image) can
be made.
Disable Executive
mode
0X Exe0]
Unlock front panel controls. All front panel
adjustments can be made.
View Executive
mode status
X 0] (or) 1]
(or) 2]
View the current status:
0 = off [default]; 1 = on, complete;
2 = on, limited adjustments.
Overscan mode (applies only to SMPTE [NTSC, PAL, 480p, 576p, 720p, 1080i, 1080p] input rates)
Set value
EX#*X2*OSCN} OscnX#*X2*]
Set input format X# to overscan mode X2*.
View status
EX#OSCN}
X2*]
Show overscan mode status for input
format X#.
HDCP notication (green screen/message)
Enable notication
EN1HDCP} HdcpN1]
Enable the HDCP notication.
Disable notification
EN0HDCP} HdcpN0]
Disable the HDCP notication; instead
mute output.
Query notification
ENHDCP}
X(]
Query the HDCP notication.
HDCP status (valid for HDMI inputs and HDMI oututs only)
Query input
EIX!HDCP}
X3#]
HdcpIX!*X3#]
Query the HDCP status of the current input
X!.
(verbose mode response)
Query output
EOX@HDCP}
X3#]
HdcpOX@*X3#]
Query the HDCP status of the HDMI output
X@.
(verbose mode response)
HDCP input authorization (valid for HDMI inputs only)
Enable HDCP
authorization
EEX!*1HDCP} HdcpEX!*1]
Enable HDCP authorization for input X!
(default).
Disable HDCP
authorization
EEX!*0HDCP} HdcpEX!*0]
Disable HDCP authorization for input X!.
Query notification
EEX!HDCP}
X4(]
Query HDCP authorization status for input
X!.
NOTE: X! = Input selection: 1 to 5
X@ = Output selection: 0 = All outputs (default), 1 = Analog (VGA, YUVp, HDTV), 2 = HDMI, 3 = 3G/HD-SDI, 4 = None
X# = Input video format: 0 = No signal detected, 1 = RGB, 2 = YUV Auto, 3 = RGBcvS, 4 = S-video, 5 = Composite,
6 = DVI/HDMI (Only available for inputs 3, 4, and 5), 7 = Auto detect (default for inputs 1 and 2)
X( = Enable/disable: 0 = Off/disable, 1 = On/enable
X2* = Overscan (applied to SMPTE [NTSC/PAL - 480p -1080p] input rates), 0 = 0.0% (default for RGB),
1 = 2.5% (default for YUV Auto, RGBcvS), 2 = 5.0% (default for S-video, Composite). See X2* for full details.
X3# = HDCP status (valid only on HDMI/DVI outputs): 0 = no sink or source detected, 1 = sink or source detected with HDCP,
2 = sink or source detected but no HDCP is present
X4( = HDMI Input HDCP authorization status: 0 = Block HDCP encryption, 1 = Allow HDCP encryption (default for inputs 3,
4, and 5)
DVS 605 • SIS Communication and Control 45
