Filter
Top Products
Chapter 4 Recording/Playback
50
4-2 Playback
1
With the SHIFT button held down, press the STATUS
button.
The process control screen
1)
appears in the video
panel.
1) When the line mode is 525(U)/525(J), SETUP appears instead of
BLACK.
Notes
• Do the following operations within 30 seconds. The
screen returns to the normal screen if no operation is
done for 30 seconds.
• The process control screen does not appear if either
of the following is true.
- The unit is being controlled from a device
connected to the REMOTE connector, and basic
menu item 006 “LOCAL FUNCTION ENABLE”
is set to “dis” or “st&ej.”
- The unit is connected to a computer by FAM or
FTP, and the computer is logged in to this unit.
To check the assignments to buttons which
select parameters
A list of button assignments appears at the bottom of
the screen when you keep the MENU button pressed.
2
Hold down the following buttons and press the RESET
button to select “PRE” (PRESET: factory preset
setting) or “VAR” (VARIABLE: adjustable setting).
Each press of the button switches between “PRE” and
“VAR.”
a) Underlined values are the factory defaults.
The figure below is an example of the screen that
appears when you hold the PLAY button down.
AUDIO
VIDEO
INPUT SEL
WARNING
KEY INHI REC INHI
INPUT CH INPUT SEL STATUS LIGHT MONITOR
HLOFFOFFON
OFFON
-30
dB
-12
-20
-40
-60
0
CH
- 15
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
26
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
37
DATA
OVER
-30
dB
-12
-20
-40
-60
0
CH-
48
BATT E F
DATA
OVER
VITC
HOURS MINUTES SECONDS FRAMES
COUNTER HOLDVIUB
PB EXT-LKNDF
DISC E B
ACCESS
SHUTTLE JOG
THUMB
NAIL
ESSENCE
MARK
MENU
S.SEL
SET
RESET
SHIFT
TOP F REV
ALL/CH-1 CH-2 CH-3 CH-4
TC
F FWD
AUDI O
END
REC
PRESET
VARIABLE
PB
PREV NEXTPLAY STOP REC
CLIP
MENU
SYSTEM
MENU
MONITOR
SEL
METER
SEL
HOLD
COUNTER
SEL
SUB
CLIP
MARK1
MARK2
IN
OUT
KEY INHI
ON
OFF
NETWORK
LOCAL
REMOTE
F-RUN
R-RUN
PRESET
REGEN
INT
EXT
RP188
L/ST/R
CHARACTER
VITC
PROCESS
CONTROL
3
4
15
MENU button
Video panel
VIDEO VAR ----- -----
CHROMA-Ph PRE ----- -----
SYNC-Ph PRE ----- -----
CHROMA VAR ----- -----
BLACK PRE ----- -----
SC-Ph PRE 000
PROCESS CONTROL V
-----
KEY ASIGN : MENU
ADJUST : KEY+JOG DIAL
PREST/VAR : KEY+RESET
EXIT : STATUS
Button Parameter Adjustment range
a)
PREV Video output level –512 to 0 to 511
PLAY Chroma output level –512 to 0
to 511
NEXT Setup/black level –512 to 0
to 511
STOP Chroma phase –128 to 0
to 127
G Output signal sync
phase
–128 to 0
to 127
g Output signal
subcarrier phase
0
to 511
VIDEO VAR ----- -----
CHROMA-Ph PRE ----- -----
SYNC-Ph PRE ----- -----
CHROMA VAR ----- -----
BLACK PRE ----- -----
SC-Ph PRE 000
PROCESS CONTROL V
-----
PREV:VIDEO (<):SYS-Ph
PLAY:CHROMA (>):SC-Ph
NEXT:SETUP or BLACK
STOP:CHROMA-ph
List of parameters assigned to buttons
CHROMA PRE ----- -----
000
PROCESS CONTROL V
-
Select “PRE” or “VAR”
Marker indicating the
position of the setting in
the adjustment range
Setting