Filter
Top Products
13
Introduction
• Some pages have no tabs.
5 To move to another page or tab, press the [MENU]
key and repeat the procedure from step 2.
The parameter value in the edit cell can be set by using
the front panel VALUE controllers ([VALUE] slider,
[ ][ ] keys, [VALUE] dial, numeric keys [0]–[9], [–]
key, [ENTER] key, and [./10’s HOLD] key). As neces-
sary, you can also use the [BANK] keys and the [COM-
PARE] key.
For some parameters, the value can be set by pressing
a popup button to display the popup menu and then
selecting a parameter value, or by holding down the
[ENTER] key and playing a note on the keyboard to
input a note number or velocity value.
VALUE controllers
[VALUE] slider
Use this when you wish to make major changes in the
value.
In Program mode and Combination mode, this slider
can also be used as a control source for alternate modu-
lation or dynamic modulation. (This is active in Pro-
gram or Combination P0: Play when the “Program
Number: name” or “Combination Number: name” (the
large characters in the upper part of the LCD) is
selected).
[ ][ ] keys
Use these when you wish to make small changes in the
value.
[VALUE] dial
Use this when you wish to make large changes in a
value.
Numeric keys [0]–[9], [ENTER] key, [–] key,
[./10’s HOLD] key
Use these when you know the parameter value that
you wish to input.
After using the numeric keys [0]–[9] to input a number,
press the [ENTER] key to finalize the parameter value.
Use the [–] key to enter negative numbers.
Use the [./10’s HOLD] key to enter a decimal point. In
Program and Combination mode P0: Play, the [./10’s
HOLD] key performs the 10’s Hold function. (
☞p.21,
p.23)
[BANK] keys
The [BANK] keys are used in Program mode to select
the program bank and in Combination mode to select
the combination bank. In Combination mode, they are
also used to select the program bank for each timbre of
the combination. In Sequencer and Song Play modes,
these keys are used to select the bank of the program
used by each track of the song.
*1
Banks A–D are rewritable user program/combina-
tion banks. The factory settings and the preset pro-
grams/combinations of the separately sold EXB-
PCM series options are provided for banks A–D.
*2
Bank E is also a rewritable user program bank (like
banks A–D). We recommend that you use bank E for
programs that you yourself create. When converting
a multisample created in Sampling mode into a pro-
gram (“Convert MS to Program”), it is best to use
bank E.
*3
Bank F is available if the separately sold EXB-MOSS
option is installed. This bank is only for programs
that use the EXB-MOSS.
*4
Banks G, g(1)–g(9), and g(d) comprise eleven banks.
They contain 256 programs compatible with GM2,
and 9 drum programs. These banks cannot be
rewritten.
Each time you press the BANK [G] key, you will
cycle through banks G, g(1)–g(9), g(d) and back to
G.
Bank G contains 128 programs for the basic GM
sounds. Banks g(1)–g(9) contain variation sounds.
Bank g(d) contains drum programs. In banks which
contain no variation sounds, the basic GM sounds
will be selected. (An asterisk * will be added to the
beginning of the program name.)
3. Setting a parameter
[BANK] key Program Combination
A
*1
Bank A (000...127) Bank A (000...127)
B
*1
Bank B (000...127) Bank B (000...127)
C
*1
Bank C (000...127) Bank C (000...127)
D
*1
Bank D (000...127) Bank D (000...127)
E
*2
Bank E (000...127) ---
F
*3
Bank F (000...127) ---
G
*4
Bank G (001...128) ---
Bank g(1) (001...128) ---
Bank g(2) (001...128) ---
:
Bank g(9) (001...128) ---
Bank g(d) (001...128) ---
Basic operation of the TRITON