Filter
Top Products
Appendices
133
Troubleshooting
If you experience problems, refer to the relevant item
and take the appropriate measures.
Power does not turn on
• Is the power cable connected to an outlet?.......☞p.15
• Is the [POWER] switch turned on?
Turn on the rear panel [POWER] switch. .........
☞p.17
Power is on, but nothing is displayed in the
LCD screen
• Use the rear panel [Contrast] knob to adjust the
contrast of the LCD screen....................................
☞p.9
Can’t operate the LCD screen correctly
• In Global P0: Basic Setup, execute the “Touch Panel
Calibration” page menu command to adjust the
sensitivity of the touch panel..................... PG
☞p.115
If it is not possible to select this command from the
page menu, enter Global mode P0 (press the
[MENU] key, and then press the [0] or [EXIT] key
to access this), and then hold down the [ENTER]
key and press numeric key [2] to display the dia-
log box.
No sound
• Are connections made correctly to your amp,
mixer, or headphones? ........................................
☞p.15
• Is your amp or mixer turned on?
• Is Local Control turned on?
In Global P1: MIDI, check the “Local Control On”
check box. ..................................................... PG
☞p.117
• Is the [VOLUME] slider raised? ...........................
☞p.6
• If there is no sound from the OUTPUT
(INDIVIDUAL) 1–4 jacks, make sure that “BUS
Select (IFX/Indiv.Out Assign)” or “Bus Select”
following the insert effect is set to 1, 2, 3, 4, 1/2, or
3/4.......................................................................
☞p.107~
• If specific tracks in Sequencer mode or Song Play
mode do not sound, Make sure that the PLAY/
MUTE/REC button or PLAY/MUTE button is set
to PLAY........................................................
☞p.62, p.88
Make sure that the “Status” is INT or BTH.
.......................................................................
☞p.59, p.85
• Are the Key Zone and Velocity Zone set so that
sound will be produced when you play? .. PG
☞p.59
Notes do not stop
• In Program P1: Edit Basic, select the Program Basic
tab, make sure that the “Hold” check box is
unchecked......................................................... PG
☞p.4
• In Global P2: Controller, make sure that “Damper
Polarity” or “Foot Switch Polarity” is set correctly.
........................................................................PG
☞p.121
Cannot input sound
• Is your audio source connected to the AUDIO
INPUT 1, 2 jacks?..................................................
☞p.78
• Is the AUDIO INPUT [LEVEL] knob raised?
.................................................................................
☞p.78
• Is the [MIC-LINE] switch set appropriately?
.................................................................................
☞p.78
• If there is no sound in Sampling mode, go to
Sampling P0: Recording, select the Input/Setup
tab, and make sure that “Level” and “BUS(IFX)
Select” are set correctly........................................
☞p.79
• If there is no sound in Program, Combination,
Sequencer, or Song Play modes, go to Global P0:
Basic Setup, select the Audio Input tab, and make
sure that “Level” and “BUS(IFX) Select” are set
correctly................................................................
☞p.109
Noise or oscillation is heard
• When using an effect on the external audio source
being input from AUDIO INPUT 1 and 2,
oscillation may occur depending on the type of
effect or on the parameter settings. Please adjust
the input level, output level, and effect parameters.
You need to be particularly careful when using a
high-gain effect.
• After a sample edit has been executed, or after a
stereo sample has been recorded, a small noise
may be heard. This has no effect on the audio data
that was edited or sampled.
• When using the BPM/MIDI Sync function to
control the delay time of an effect, noise may occur
in the delay sound. This noise is due to
discontinuities in the delay sound, and is not a
malfunction.
Effects are not applied
• Are the Global P0: Basic tab “IFX1–5 Off,” “MFX1
Off,” or “MFX2 Off” settings checked? ...........
☞p.125
• If you are in Combination, Sequencer, or Song Play
modes, and master effects are not applied when
you raise the “Send 1” or “Send 2” of the timbre/
track, does “Return 1” or “Return 2” from the
master effect need to be raised?........................
☞p.108
Alternatively, has “Send 1” or “Send 2” for each
oscillator of the program used by the timbre/track
been lowered? ................................................PG
☞p.24
The actual send level is determined by multiplying
the send setting of each oscillator in the program
Troubleshooting