Filter
Top Products
67
Enjoying Music in the Remote Zone—Continued
To enjoy movies and audio in the remote zone (Zone 2),
you need to perform the remote zone settings.
The procedures shown below assume using the remote
controller. When performing these procedures using the
front panel, use the buttons corresponding to the ones on
the remote controller.
Note:
When the SURR BACK/ZONE 2 outputs (SPEAKERS
and PRE OUT) are set to Zone 2, listening modes that
need surround back speakers (i.e., Dolby Digital EX,
DTS-ES, and THX Surround EX) are not available.
Performing the Settings for the
Remote Zone (Zone 2)
1
Press the scroll wheel, and then
press the Setup button to display
the main menu on the monitor and
front display.
2
Use the and cursor buttons to
select “0. Hardware Setup” and
then press the Enter button.
The “Hardware Setup” menu appears.
When the “Hardware Setup” menu item
does not appear, select “→Advanced
Menu” to display the “Advanced Menu.”
--
/
---
@.
-
'
/ ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
TV CH
TV VOL
+
10 0
123
456
789
+
-
+
-
Direct Tuning
Custom
Display
Dimmer
T
V
Input
Sleep
Muting
T
V
On Standby
A
u
d
i
o
A
D
J
E
x
i
t
G
u
i
d
e
Random
Step
/
Slow
Rec
Clear
Input
T
o
p
M
e
n
u
M
e
n
u
S
e
t
u
p
R
e
t
u
r
n
Zone
2
InputMode
Macro
CH
VOL
Disc
Enter
Master Volume
Standby/On
UpsamplingPure Audio
Audio
Selector
Tape
Tuner Phono Net AudioCD
Video 1
VCR 1
Video 3
Video 2
VCR 2
Video 4 Video 5
DVD
Zone 2
()
GRN
Rec
()
RED
A
-
FO
RM Listening Mode Memory
Video 5 Input
StereoDirect
/
Pure Audio
DSP
Surround THX
Clear
Rec Out
Zone 2 Of
f
Setup
Tuning
Preset
Enter
Return
DimmerDisplay
S Video
Audio
Video L R
Phones
Standby
Memory FM Mode
DTR
-
7.4
Digital
Setup
Enter
Setup
Enter
///
///
[ENTER]Quit:[SETUP]
Advanced Menu
0.Hardware Setup
1.Speaker Setup
2.Input Setup
3.Audio Adjust
4.Preference
5.Network Setup
→
Basic Menu
0.Hardware Setup
1.Speaker Impedance
2.Surr Back/Zone2
3.Remote Setup
4.TV Format
[ENTER]Quit:[SETUP]
Enter
Enter
3
When you connect speakers
whose impedance values are
between 4 and 6 ohms, select
“Speaker Impedance” to display
the sub-menu and set the value for
the “Minimum” to “4 ohms.”
For details, see page 30.
Even if you connect some speakers whose
impedance values are between 6 and 16
ohms among speakers whose impedance
values are between 4 and 6 ohms, set the
“Minimum” value to “4 ohms.”
4
Use the and cursor buttons to
select “Surr Back/Zone 2” and
then press the Enter button.
The “Surr Back/Zone 2” menu appears.
5
Use the and cursor buttons
to select “Zone 2” or “Surr Back.”
Surr Back: Use the SURR BACK/
ZONE 2 outputs (SPEAKERS and PRE
OUT) as surround back outputs.
Select this option when connecting a receiver/
integrated amp in Zone 2 (see page 66).
Zone 2: Use the SURR BACK/ZONE 2 out-
puts (SPEAKERS or PRE OUT) for Zone 2.
Select this option when connecting a power
amp or only speakers in Zone 2 (see page 66).
6
Press the Setup button to return to
the main menu.
0-1.Speaker Impedance
a.Minimum :6 ohms
Quit:[SETUP]
Enter
Enter
0-2.Surr Back/Zone2
a.Surr Back/Zone2
:Zone2
Quit:[SETUP]
Making Full Use of Your DTR-7.4