Filter
Top Products
72
4. Press one of the learning buttons, to which you
want to assign a signal from the target remote
control.
The LEARN indicator starts flashing.
• If you have pressed DVD or DVD MULTI in step 3, you can
store the signals into the following buttons.
• If you have pressed PHONO in step 3, you can store the
signals into the following buttons.
• If you have pressed CD, or CONTROL to select “CD DISC,”
in step 3, you can store the signals into the following buttons.
– You can store a different set of signals into the following
buttons separately for “CD” and “CD DISC.”
• If you have pressed “TAPE/MD” or “CDR” in step 3, you can
store the signals into the following buttons.
• If you have pressed VCR1 in step 3, you can store the signals
into the following buttons.
TV
CATV/
DBS
LEARN
CHANNEL
TV/VIDEO
TV VOL
EFFECT
ROOM SIZE
FM MODE
RETURN
100
+
WALL
LIVENESS
123
456
7
/P 89
10
+
100
STANDBY/ON
TV/CATV/DBS
For the main room
operations
For the sub-room
operations
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
TRANSMITLEARN
MAIN ROOM
• If you have pressed “TV/DBS” in step 3, you can store the
signals into the following buttons:
– By setting the TV operation mode selector
either to “TV” or “CATV/DBS,” you can store
a different set of signals into the following
buttons.
5. While the LEARN indicator is flashing, press the
button on the target remote control.
The signal from the target remote control is sent to this remote
control.
“LEARN OK” appears and the LEARN indicator stops flashing
and remains lit. The target signal is now stored in the button
selected in step 4.
Notes:
• If the LEARN indicator stops flashing before you press the
button on the target remote control, repeat from step 4 again.
• If “ERROR” appears on the display, you have failed in storing
the signal. Try again. However some signals do not match to
this remote control even though this remote control can learn
most infrared signals.
6. • Repeat steps 4 to 5 to store more signals in the
same remote mode (source).
• Repeat steps 3 to 5 to store more signals in a
different remote mode (source).
7. Set the LEARN/TRANSMIT (MAIN ROOM/
SUB ROOM) selector to “TRANSMIT (MAIN
ROOM/SUB ROOM)” to finish the storing
procedure.
Notes:
• The signals stored into this remote control from the target remote
control deviate slightly from the original signals. Since some
components will not accept these deviating signals, you may not be
able to operate those components using this remote control even
though the storing procedure has been successfully finished.
• When replacing the batteries, finish it without delay; otherwise, the
stored signals are all erased.
SET
DVD
MENU
TUNING
STOP PAUSE
FF/
/ REW
PLAY
DOWN UP
EFFECT
ROOM SIZE
FM MODE
RETURN
100
+
WALL
LIVENESS
123
456
7
/P
89
10
+
100
TUNING
STOP
PLAY
TUNING
STOP PAUSE
FF/
/ REW
PLAY
DOWN UP
EFFECT
ROOM SIZE
FM MODE
RETURN
100
+
WALL
LIVENESS
123
456
7
/P
89
10
+
100
TUNING
STOP PAUSE
FF/
/ REW
REC
PLAY
DOWN UP
EFFECT
ROOM SIZE
FM MODE
RETURN
100
+
WALL
LIVENESS
123
456
7
/P
89
10
+
100
TUNING
STOP PAUSE
FF/
/ REW
PLAY
DOWN UP
CHANNEL
EFFECT
ROOM SIZE
FM MODE
RETURN
100
+
WALL
LIVENESS
123
456
7
/P
89
10
+
100
REC
STANDBY/ON
VCR 1
EN61-77_RX-DP10VBK[J]_f 01.6.19, 0:54 PM72