Filter
Top Products
36
Setting the Speaker Distance
—SPEAKER DISTANCE (2)
The distance from your listening
point to the speakers is another
important element to obtain the
best possible surround sound of
the Surround and DSP modes.
You need to set the distance from
your listening point to the
speakers.
By referring to the speaker distance setting, this unit automatically
sets the delay time of the sound through each speaker so that sounds
through all the speakers can reach you at the same time.
7
For measuring unit:
Select one of the following.
meter : Select this to set the distance by meter.
feet : Select this to set the distance by feet.
7
For each speaker:
Set the distance from the listening point within the range of
0.30 m (1.0 ft) to 9.00 m (30.0 ft), in 0.15 m (0.5 ft) intervals.
Notes:
• You cannot set the speaker distance for the speaker you have
selected “NO” or “NONE” for on the SPEAKER SETTING
submenu.
• This setting is not valid for the DVD MULTI playback mode.
Setting the Speakers
—SPEAKER SETTING (1)
To obtain the best possible
surround sound of the Surround
and DSP modes in the main
room, you have to register the
information about the speaker
arrangement after all connections
are completed.
7
For subwoofer:
Select one of the following.
YES : Select this when a subwoofer is connected.
NO : Select this when no subwoofer is used.
7
For front speakers, center speaker, surround
speakers, and surround back speakers:
Select one of the following.
LARGE : Select this when the speaker size is relatively large.
SMALL : Select this when the speaker size is relatively small.
NONE : Select this when you have not connected a speaker.
(Not selectable for the front speakers)
Notes:
• Keep the following comment in mind as reference when
adjusting.
– If the size of the cone speaker unit built in your speaker is
greater than 12 cm (4
3
/
4
inches), select “LARGE,” and if it is
smaller than 12 cm (4
3
/
4
inches), select “SMALL.”
• If you have selected “NO” for the subwoofer, you can only
select “LARGE” for the front speakers.
• If you have selected “SMALL” for the front speakers, you
cannot select “LARGE” for the center, surround, and surround
back speakers.
• If you have selected “SMALL” for the surround speakers, you
cannot select “LARGE” for the surround back speakers.
• If you have selected “NONE” for the surround speakers, the
surround back speakers are fixed to “NONE.”
EX. In the above case, set the speaker distance as follows:
Subwoofer (SUBWFR) SUBWOOFER: 3.60 m (12.0 ft)
Left front (L) FRONT L SP: 3.00 m (10.0 ft)
Right front (R) FRONT R SP: 3.00 m (10.0 ft)
Center (C) CENTER SP: 3.00 m (10.0 ft)
Left surround (LS) SURR L SP: 2.40 m (8.0 ft)
Right surround (RS) SURR R SP: 2.40 m (8.0 ft)
Left surround back (LSB)
SBACK L SP: 2.70 m (9.0 ft)
Right surround back (RSB)
SBACK R SP: 2.70 m (9.0 ft)
2.1 m
(7 ft)
2.4 m
(8 ft)
2.7 m
(9 ft)
3.0 m
(10 ft)
3.3 m
(11 ft)
3.6 m
(12 ft)
C
LR
SUBWFR
LS RS
LSB
RSB
30˚
90˚
60˚ 60˚
90˚
30˚
:OPERATE :BACK
SPEAKER DISTANCE
UNIT : meter
SUBWOOFER : 3.00m
FRONT L SP : 3.00m
FRONT R SP : 3.00m
CENTER SP : 3.00m
SURR L SP : 3.00m
SURR R SP : 3.00m
SBACK L SP : 3.00m
SBACK R SP : 3.00m
:OPERATE
:BACK
SPEAKER SETTING
SUBWOOFER : NO
FRONT SP : LARGE
CENTER SP : SMALL
SURROUND SP : SMALL
SURR BACK SP : SMALL
EN33-40_RX-DP10VBK[J]_f 2001.6.28, 10:05 AM36