Filter
Top Products
67
Operating Other Manufacturers’ Equipment
You can use this remote control supplied for this unit for operating the other manufacturers’ components, either by
changing the preset signal codes or by using the learning function (see page 71).
Changing the Preset Signal Codes
By changing the transmittable signals from preset ones to the other
manufacturers’, you can operate the other manufacturer’s
components using this remote control.
• When operating the other manufacturers’ components, refer also
to the manuals supplied with them.
To change the transmittable signals for
operating another manufacturer’s TV
1. Set the TV operation mode selector to
“TV.”
2. Press and hold TV/CATV/DBS
(STANDBY/ON).
3. Press TV/DBS.
4. Enter manufacturer’s code
using buttons 1–9, and 0.
See page 69 to find the code.
5. Release TV/CATV/DBS (STANDBY/ON).
After setting the TV operation mode selector to “TV,” you can
perform the following operations on the TV:
TV/CATV/DBS
(STANDBY/ON):
Turns on or off the TV.
TV VOL +/– : Adjusts the volume.
TV/VIDEO : Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the TV operation mode selector
set to “TV”), you can perform the following operations on a TV:
CHANNEL +/– : Changes the channels.
1 – 10, 0, 100+ (+10) : Selects the channels.
Number button 10 will function as
the ENTER button if your TV
requires pressing ENTER after
selecting a channel number.
Notes:
• Refer to the manual supplied for your TV.
• All the functions listed above may not be assigned to the
buttons for some TVs.
• If you cannot change the channels of some TVs by pressing
number buttons, press CHANNEL +/– for changing the channels.
6. Try to operate your TV by pressing
TV/CATV/DBS
(STANDBY/ON).
When your TV turns on or off, you have entered
the correct code.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
IMPORTANT:
• To operate the other component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
–Place the IR signal transmitter so that it is aimed at the remote
sensor(s) on the target component(s).
–The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
–The IR signal transmitter can send signals at a distance of 10 feet
(3 m).
When using the remote control:
–Set the MAIN ROOM/SUB ROOM (LEARN/TRANSMIT) selector to
“MAIN ROOM” or “SUB ROOM” correctly.
–Set the TV operation mode selector to “TV” or
“CATV/DBS” correctly.
To operate TV, set it to “TV.”
To operate the CATV converter or the DBS tuner, set it
to “CATV/DBS.”
–Check the indication shown on the remote’s display
when you press a button—this indicates the remote control
operation mode together with multi-room operation mode (either
MAIN ROOM or SUB ROOM) for a while (10 or 5 seconds).
TV
CATV/
DBS
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
TRANSMITLEARN
MAIN ROOM
Ex.When you press VCR1
with MAIN ROOM/SUB
ROOM (LEARN/
TRANSMIT) selector
set to “MAIN ROOM.”
Ex.When you press VCR1
with MAIN ROOM/SUB
ROOM (LEARN/
TRANSMIT) selector
set to “SUB ROOM.”
ON/OFF ON/OFF
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
MAIN ROOM
MAIN ROOM
STANDBY/ON STANDBY/ON
STANDBY
TV/CATV/DBS
VCR 1
ON
ON/OFF ON/OFF
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
MAIN ROOM
SUB ROOM
STANDBY/ON STANDBY/ON
STANDBY
TV/CATV/DBS
VCR 1
ON
CAUTION:
When replacing the batteries, finish it without delay; otherwise,
manufactures’ codes are lost.
TV
CATV/
DBS
TV/CATV/DBS
STANDBY/ON
TV/DBS
Remote’s display
EFFECT
ROOM SIZE
FM MODE
RETURN
100
+
WALL
LIVENESS
123
456
7
/P
89
10
+
100
TV/CATV/DBS
STANDBY/ON
EN61-77_RX-DP10VBK[J]_f 01.6.19, 0:54 PM67