Filter
Top Products
64
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC
components are preset in the remote control.
Operating Audio Components
Tuner
You can always perform the following operations:
FM : Tunes into the last selected FM station.
AM : Tunes into the last selected AM station.
After pressing FM or AM, you can perform the following operations:
1 – 10, +10 : Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then
10.
TUNING UP/DOWN : Tunes into stations.
FM MODE : Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations:
THX ON/OFF : Turns on or off the THX Surround
modes—TH X Surround EX or THX
Cinema.
SURROUND ON/OFF : Turns on or off the conventional
Surround modes—Dolby Digital, DTS
Surround, and Dolby Pro Logic.
DSP MODE : Selects the DSP modes.
TEST : Turns on or off the test tone output.
After pressing SOUND, you can perform the following operations:
FRONT•L then LEVEL +/– : Adjusts the left front speaker
channel output level.
FRONT•R then LEVEL +/–: Adjusts the right front speaker
channel output level.
SUBWFR then LEVEL +/– : Adjusts the subwoofer output level.
CENTER then LEVEL +/– : Adjusts the center speaker channel
output level.
SURR•L then LEVEL +/– : Adjusts the left surround speaker
channel output level.
SURR•R then LEVEL +/– : Adjusts the right surround speaker
channel output level.
SURR BK•L then LEVEL +/– :
Adjusts the left surround back
speaker channel output level.
SURR BK•R then LEVEL +/– :
Adjusts the right surround back
channel speaker output level.
EFFECT : Selects the effect level.
ROOM SIZE : Selects the room size.
LIVENESS : Selects the liveness.
WALL : Selects the wall type.
LINE DIRECT : Turns on or off Line Direct.
CC CONVERTER : Turns on or off CC Converter.
Notes:
• After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the 10 keys;
otherwise, the 10 keys cannot be used for operating your target
source.
• Each time you press LEVEL + or LEVEL –, the corresponding
speaker name appears on the remote’s display.
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK (SYNCHRO) jacks (see page 54) in addition to the
connections using cables with RCA pin plugs (see pages 9 and 10).
• Aim the remote control directly at the remote sensor on the
receiver.
• To operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 25.)
• Refer also to the manuals supplied with your components.
When using the remote control:
–Set MAIN ROOM/SUB ROOM (LEARN/TRANSMIT) selector to
“MAIN ROOM” or “SUB ROOM” correctly.
–Check the indication shown on the remote’s display when you press
a button—this indicates the remote control operation mode together
with multi-room operation mode (either MAIN ROOM or SUB
ROOM) for a while (10 or 5 seconds).
–The CONTROL button can change the remote control operation
mode without changing the source.
Each time you press the button, the remote control operation mode
changes in the sequence—
VCR1 = TAPE =
CDR = CD DISC =
(back
to the beginning).
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
TRANSMITLEARN
MAIN ROOM
Ex.When you press FM
with MAIN ROOM/SUB
ROOM (LEARN/
TRANSMIT) selector
set to “MAIN ROOM.”
Ex.When you press FM
with MAIN ROOM/SUB
ROOM (LEARN/
TRANSMIT) selector
set to “SUB ROOM.”
ON/OFF ON/OFF
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
MAIN ROOM
MAIN ROOM
STANDBY/ON STANDBY/ON
STANDBY
TV/CATV/DBS
VCR 1
ON
ON/OFF ON/OFF
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
MAIN ROOM
SUB ROOM
STANDBY/ON STANDBY/ON
STANDBY
TV/CATV/DBS
VCR 1
ON
EN61-77_RX-DP10VBK[J]_f 01.6.19, 0:54 PM64