Filter
Top Products
45
7
Adjustment procedure on this submenu
1 Press fi or % (DOWN or UP) to select the channel—
FRONT, CENTER, SURROUND, or SURROUND BACK,
then press SET.
The adjustment screen of the selected item appears.
2 Press fi or % (DOWN or UP) to select an item you want to
adjust on the selected adjustment screen.
3 Press # or @ (RIGHT or LEFT) to adjust the item.
• Once one of the sound levels—“BASS LEVEL,” “MID
LEVEL” and “TREBLE LEVEL”—is adjusted, the
PARAMETRIC EQ indicator lights up on the display.
4 Repeat steps 2 and 3 to adjust the other items on the same
adjustment screen.
5 Press EXIT once.
The PARAMETRIC EQ submenu appears again.
6 Repeat steps 1 to 5 to adjust the other channels.
To cancel the adjustment, set all the sound levels—“BASS
LEVEL,” “MID LEVEL” and “TREBLE LEVEL”—to “0 dB.”
The PARAMETRIC EQ indicator goes off.
7
Adjustment screen
On these adjustment screens, you can adjust the following items for
each channel signal.
BASS FREQ* : Select the center frequency to adjust bass
sounds from
—63 Hz, 80 Hz, 100 Hz (initial), 125 Hz,
160 Hz, 200 Hz, 250 Hz, 320 Hz, 400 Hz,
500 Hz, 630 Hz, 800 Hz, 1.0 kHz
BASS LEVEL : Adjust the enhancement level for bass sounds
(with in the range of +6 dB to –6 dB).
MID FREQ* : Select the center frequency to adjust
middle-range sounds from
—250 Hz, 320 Hz, 400 Hz, 500 Hz, 630 Hz,
800 Hz, 1.0 kHz (initial), 1.25 kHz, 1.6 kHz,
2.0 kHz, 2.5 kHz, 3.2 kHz, 4.0 kHz
MID LEVEL : Adjust the enhancement level for middle-
range sounds (with in the range of +6 dB
to –6 dB).
TREBLE FREQ* : Select the center frequency to adjust treble
sounds from—1.0 kHz, 1.25 kHz, 1.6 kHz,
2.0 kHz, 2.5 kHz, 3.2 kHz, 4.0 kHz, 5.0
kHz, 6.3 kHz, 8.0 kHz, 10.0 kHz (initial),
12.5 kHz, 16.0 kHz
TREBLE LEVEL : Adjust the enhancement level for treble
sounds (with in the range of +6 dB to –6 dB).
Adjusting the DSP Parameters
—DSP PARAMETER (3)
On this submenu, you can adjust
DSP parameters.
• This submenu is available only
when the DSP mode* is on,
and the settings made apply
only to the DSP mode*
(*except All Channel Stereo).
Note:
When the front speakers are deactivated, you cannot adjust the DSP
parameters.
7
Adjusting the DSP parameters
Select and adjust the following parameters:
EFFECT LEVEL: Adjust the DSP effect level.
As the number increases, the DSP effect becomes stronger.
(Normally select “3.” Adjustable range: 1 to 5)
ROOM SIZE: Adjust the virtual room size. As the number
increases, the interval between reflections increases so that
you will feel as if you were in a larger room. (Normally
select “3.” Adjustable range: 1 to 5)
LIVENESS: Adjust the liveness effect. As the number
increases, the attenuation level of reflections over time
decreases so that acoustics change from “Dead” to “Live.”
(Normally select “3.” Adjustable range: 1 to 5)
WALL TYPE: Adjust the wall type. As the number increases, the
hardness of the wall to be simulated seems to become “soft” to
“hard.” (Normally select “3.” Adjustable range: 1 to 5)
SEAT POSITION: Select this to either 1 or 2 according to your
preference as if you change your seat in a theater, hall,
recital hall, church, etc.
Adjusting the Center Channel
—CENTER CHANNEL (4)
On this submenu, you can set
center channel signal adjustment
for the DSP modes.
• This submenu is available only
when the DSP mode* is on,
and the settings made apply
only to the DSP mode*
(*except All Channel Stereo).
7
Cutting off the high frequency range in the center
channel
Cut off the high frequency range signals in the center channel.
ON : Select this to cut off the high frequency range signals.
OFF : Select this not to cut off the high frequency range
signals.
7
Setting the center channel alignment
Align the vertical localization of the center channel signals
(mainly human voices are recorded) at the same height as for the
front speakers.
ON : Select this when you cannot feel the actors or singers are
not speaking or singing on the screen.
OFF : Center channel alignment is turned off.
PEQ SURROUND
BASS FREQ : 100Hz
BASS LEVEL : 0dB
MID FREQ : 1.0kHz
MID LEVEL : 0dB
TREBLE FREQ :10.0kHz
TREBLE LEVEL: 0dB
PEQ SURR BACK
BASS FREQ : 100Hz
BASS LEVEL : 0dB
MID FREQ : 1.0kHz
MID LEVEL : 0dB
TREBLE FREQ :10.0kHz
TREBLE LEVEL: 0dB
PEQ CENTER
BASS FREQ : 100Hz
BASS LEVEL : 0dB
MID FREQ : 1.0kHz
MID LEVEL : 0dB
TREBLE FREQ :10.0kHz
TREBLE LEVEL: 0dB
PEQ FRONT
BASS FREQ : 100Hz
BASS LEVEL : 0dB
MID FREQ : 1.0kHz
MID LEVEL : 0dB
TREBLE FREQ :10.0kHz
TREBLE LEVEL: 0dB
:OPERATE
:BACK
DSP PARAMETER
EFFECT LEVEL :3
ROOM SIZE :3
LIVENESS :3
WALL TYPE :3
SEAT POSITION:1
CENTER CHANNEL
CENTER EQ : OFF
CENTER ALINMENT: OFF
:OPERATE
:BACK
* Adjustable range changes according to the other two frequency
settings.
EN41-45_RX-DP10VBK[J]_f 01.6.21, 6:02 PM45