Filter
Top Products
68
To change the transmittable signals for
operating a CATV converter and DBS tuner
1. Set the TV operation mode selector to
“CATV/DBS.”
2. Press and hold TV/CATV/DBS
(STANDBY/ON).
3. Press TV/DBS.
4. Enter manufacturer’s code using
buttons 1–9, and 0.
See page 70 to find the code.
5. Release TV/CATV/DBS (STANDBY/ON).
After setting the TV operation mode selector to “CATV/DBS,”
you can turn on and off the CATV convertor or the DBS tuner:
TV/CATV/DBS
(STANDBY/ON):
Turns on or off the CATV
converter or DBS tuner.
After pressing TV/DBS (with TV operation mode selector set to
“CATV/DBS”), you can perform the following operations on the
CATV convertor or on the DBS tuner:
CHANNEL +/– : Changes the channels.
1 – 10, 0, 100+ (+10) : Selects the channels.
Number button 10 will function as the
ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
Note:
Refer to the manual supplied for your CATV convertor or DBS
tuner.
6. Try to operate your CATV converter
or DBS tuner by pressing TV/CATV/
DBS
(STANDBY/ON).
When your CATV converter or DBS tuner turns
on or off, you have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct
one is entered.
Note:
You cannot preset the signals for both of the CATV converter and DBS
tuner at the same time.
TV
CATV/
DBS
To change the transmittable signals for
operating another manufacturer’s VCR
1. Press and hold VCR 1
(STANDBY/ON).
2. Press VCR 1.
3. Enter manufacturer’s code using
buttons 1–9, and 0.
See page 70 to find the code.
4. Release VCR 1 (STANDBY/ON).
The following button can be used for operating the
VCR :
VCR 1 (STANDBY/ON):
Turns on or off the VCR.
After pressing VCR 1, you can perform the following operations
on the VCR:
1 – 10, 0, 100+ (+10) : Selects the TV channels.
Number button 10 will function as
the ENTER button if your VCR
requires pressing ENTER after
selecting a channel number.
PLAY : Starts playback.
REW : Rewinds a video tape.
FF : Fast-winds a video tape.
STOP : Stops operation.
PAUSE : Pauses.
¶ REC : Press this button together with the PLAY
button to start recording (only for the main
room operation).
Press this button together with the PAUSE
button to enter recording pause (only for the
main room operation).
CHANNEL +/– : Changes the TV channels on the VCR.
Note:
Refer to the manual supplied for your VCR.
5. Try to operate your VCR by pressing
VCR 1
(STANDBY/ON).
When your VCR turns on or off, you have entered
the correct code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Remote’s display
TV/CATV/DBS
STANDBY/ON
TV/CATV/DBS
STANDBY/ON
VCR 1
Remote’s display
TV/DBS
EFFECT
ROOM SIZE
FM MODE
RETURN
100
+
WALL
LIVENESS
123
456
7
/P
89
10
+
100
VCR 1
STANDBY/ON
VCR 1
STANDBY/ON
EFFECT
ROOM SIZE
FM MODE
RETURN
100
+
WALL
LIVENESS
123
456
7
/P
89
10
+
100
EN61-77_RX-DP10VBK[J]_f 01.6.19, 0:54 PM68