Filter
Top Products
52
*
When multichannel signals come in, you cannot select “STEREO
FILM” and “MONO FILM.”
Notes:
• When the surround speakers are deactivated, the 3D-PHONIC
processing is applied to the DSP modes (the 3D-PHONIC indicator
also lights up).
• If “USER MODE 1” (then “NO DATA”) appears, press and hold DSP
MODE on the unit until it disappears. (This mode is only for service
personnel.)
To cancel the DSP modes
Press DSP MODE repeatedly until “SURROUND OFF” appears on
the display.
• When a pair of headphones is connected or when the front
speakers are deactivated, “HEADPHONE” will appear.
If you want to modify the stored sound adjustments
temporarily
See “Adjusting Surround Sounds Temporarily” on page 49.
• When adjusting the surround sounds for the DSP modes, you
cannot output the test tone.
• When you select “3D THEATER,” you cannot adjust the
surround speaker levels and surround back speaker levels.
Adjusting the DSP Parameters Temporarily
Activating the DSP mode for a source automatically recalls the
memorized DSP parameter settings done on the Adjustment
Menu.
However, if you want to modify the stored adjustments temporarily
only for the current playback source, you can use the number
buttons on the remote control.
IMPORTANT:
Check to see if the following before or while using the buttons and
controls.
For the main room operations:
The MAIN ROOM ON/OFF lamp on the unit is lit.
• When using the remote control:
–Set the MAIN ROOM/SUB ROOM (LEARN/TRANSMIT) selector
to “MAIN ROOM.”
–Check the indication shown on the remote’s display when you
press a button—this indicates the remote control operation mode
together with multi-room operation mode (either MAIN ROOM or
SUB ROOM) for a while (10 or 5 seconds).
Before you start, remember...
• Adjustments using the number buttons are temporary and
cannot be stored.
When you change the source or turn off the power, the
adjustments are erased.
• When you select “ALL CH STEREO,” you cannot adjust the DSP
parameters.
1. Press SOUND.
The 10 keys are activated for sound adjustments.
2. Press EFFECT to adjust the overall
level of the effect.
• Each time you press the button, the effect
level changes as follows:
As the number increases, the selected DSP effect becomes
stronger. (Normally set it to “EFFECT 3.”)
3. Press ROOM SIZE to adjust the room
size (sense of spaciousness).
• Each time you press the button, the display
changes to show the following:
As the number increases, the interval between reflections
increases so that you will feel as if you were in a larger room.
(Normally set it to “ROOM SIZE 3.”)
4. Press LIVENESS to adjust the
liveness.
• Each time you press the button, the display
changes to show the following:
As the number increases, the attenuation level of reflections
over time decreases so that acoustics change from “Dead” to
“Live.” (Normally set it to “LIVENESS 3.”)
5. Press WALL to adjust the wall type.
• Each time you press the button, the display
changes to show the following:
As the number increases, the hardness of the wall to be
simulated changes from “Soft” to “Hard.” (Normally set it to
“WALL TYPE 3.”)
Notes:
• You cannot adjust “SEAT POSITION” using the number buttons. If
you want to adjust it, see page 45.
• When the front speakers are deactivated, you cannot adjust the
DSP parameters.
ROOM SIZE 1
ROOM SIZE 5 ROOM SIZE 4
ROOM SIZE 2 ROOM SIZE 3
LIVENESS 1
LIVENESS 5 LIVENESS 4
LIVENESS 2 LIVENESS 3
ROOM SIZE
6
SOUND
EFFECT
3
EFFECT 1 EFFECT 2 EFFECT 3
EFFECT 4EFFECT 5
LIVENESS
9
100
+
WALL
+
10
WALL TYPE 1
WALL TYPE 5 WALL TYPE 4
WALL TYPE 2 WALL TYPE 3
ON/OFF ON/OFF
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
MAIN ROOM
MAIN ROOM
STANDBY
TV/CATV/DBS
STANDBY/ON STANDBY/ON
VCR 1
ON
SUB ROOM
TRANSMITLEARN
MAIN ROOM
Ex.When you press SOUND with
MAIN ROOM/SUB ROOM (LEARN/TRANSMIT)
selector set to “MAIN ROOM.”
EN46-53_RX-DP10VBK[J]_f 01.6.21, 6:09 PM52