Filter
Top Products
23
Activating the Main Room Front Speakers
When shipped from the factory, both pairs of the front speakers have
been set to be used in the main room.
• To use the front speakers connected to the FRONT 2/SUB ROOM
SPEAKERS terminals in the sub-room, see “Preparing for the
Sub-Room Operations—SUB ROOM” on page 40, and
“Activating the Sub-Room Front Speakers” on page 30.
IMPORTANT:
You can activate two pairs of the front speakers at the same time only
when the SPEAKER LOAD SELECTOR switch on the rear panel is
set to the “HIGH” position and when signals are sent only to the front
speakers. Otherwise, activating one pair of the speakers deactivates
the other.
On the unit ONLY:
When you have connected two pairs of the front speakers and place
them in the main room, you can select which to use.
To use the speakers connected to the FRONT
1 SPEAKERS terminals, press SPEAKERS 1
(inside the front door) so that the speakers 1
indicator lights up on the display. (Make sure
that the front speakers 2 indicator is not lit on the display.)
To use the speakers connected to the FRONT 2/SUB ROOM
SPEAKERS terminals, press SPEAKERS 2/SUB ROOM (inside
the front door) so that the front speakers 2 indicator lights up on the
display. (Make sure that the front speakers 1 indicator is not lit on
the display.)
To use both sets of the speakers, press SPEAKERS 1 and
SPEAKERS 2/SUB ROOM so that the front speakers 1 and 2
indicators light up on the display.
To use neither sets of the speakers, press SPEAKERS 1 and
SPEAKERS 2/SUB ROOM so that the front speakers 1 and 2
indicators disappear from the display.
(“HEADPHONE” appears on the unit’s display).
Note:
In the following cases, the speakers connected to the FRONT 2/SUB
ROOM SPEAKERS terminals are deactivated even if both pairs of the
front speakers are activated.
– If you select “DVD MULTI” as the source.
– If you select any of the Surround/DSP modes which activates the
center and/or surround speaker(s).
Listening only with headphones:
Sounds through the front speakers and the subwoofer shut off when
connecting a pair of headphones to the PHONES jack.
(“HEADPHONE” appears on the unit’s display.)
You can enjoy the following sounds through the headphones:
• If the Surround mode is activated, you can enjoy surround effect.
(For details, see “3D HEADPHONE Mode” on page 47.)
• If a DSP mode is activated, you can enjoy the DSP effect. (For
details, see “HEADPHONE Mode” on page 51.)
CAUTION:
Be sure to turn down the volume before connecting or putting on
headphones, as high volume can damage both the headphones and
your hearing.
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using the
digital terminals (see page 14), you need to select the digital input
mode.
Before you start, remember...
• The digital input (DIGITAL IN) terminal setting should be
correctly done for the sources you want to select the digital
input mode for (see “Setting the Digital Input Terminals—
DIGITAL IN” on page 38). Without setting this digital input
terminal correctly, you cannot change the input mode from analog
input to digital input even if you follow the procedure below.
• The digital input can be used for the main room sources. The
analog input is always selected as the sub-room source without
respect to this setting.
1. Press one of the source selecting buttons (DVD,
VCR1, TV/DBS, CD, CDR, or TAPE/MD)* for
which you want to change the input mode.
Note:
* You can select the digital input only for the sources which you
have selected the digital input terminals for. (See “Setting the
Digital Input Terminals—DIGITAL IN” on page 38.)
In addition, when “TAPE” has been assigned as the source
name to the TAPE/MD button, it does not work in this step.
To change the source name, see “Changing the Source Name”
on page 25.
2. Press INPUT MODE/INPUT ATT (or ANALOG/
DIGITAL INPUT) to change the input mode.
• Each time you press the button, the input mode changes as
follows:
SPEAKERS 1
SPEAKERS 2
/ SUB ROOM
DVD DVD MULTI VCR 1 VCR 2 TV/DBS CDVIDEO PHONO TAPE/MD CDR FM AM
On the unit
On the remote control
INPUT MODE
/ INPUT ATT
On the remote control
L
ANALOG
SPEAKERS
VOLUME
1
SUBWFR
R
dB
L
DIGITAL AUTO
DIGITAL
SPEAKERS
VOLUME
1
SUBWFR
R
LFE
RSLS
dB
On the unit
(inside the front door)
ANALOG/DIGITAL
INPUT
DVD
DVD MULTI
CD
CDR
PHONO
TAPE/MD
AM
VCR 1 VCR 2
FMVIDEOTV/DBS
EN17-30_RX-DP10VBK[J]_f 01.6.21, 5:35 PM23