Filter
Top Products
54
COMPU LINK – 4
(SYNCHRO)
COMPU LINK Remote Control System
The COMPU LINK remote control system allows you to operate JVC audio components through this receiver.
To use this remote control system, you need to connect JVC audio
components through the COMPU LINK (SYNCHRO) jacks (see
below) in addition to the connections using cables with RCA pin
plugs (see pages 9 and 10).
• Make sure that the AC power cords of these components are
unplugged before connection. Plug the AC power cords only after
all connections are complete.
Notes:
• There are four versions of COMPU LINK remote control system.
This receiver is equipped with the fourth version—COMPU LINK-4.
This version is created by adding systematic operations with the
CD recorder to the previous version—COMPU LINK-3.
• If your audio component has two COMPU LINK jacks, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
is the last item in the series of components. (For example, the
turntable or CD player on the left column.)
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 25.)
• Refer also to the manuals supplied for your audio components.
This remote control system allows you to use four functions listed
below.
Remote Control through the Remote Sensor on the
Receiver
You can control the connected audio components through the
receiver using this remote control. For details, see pages 64 and 65.
Automatic Source Selection
• When you press the play (
33
33
3) button on a connected component or
on its own remote control, the receiver automatically turns on and
changes the
main room source to the component.
– If the receiver is already turned on with the SUB ROOM ON/OFF
lamp on the unit lit, and source name for the sub-room appears on the
display, the receiver changes the
sub-room source to the component.
• When you press PLAY on the remote control
supplied for this receiver, the receiver
automatically turns on and changes the main
room source or sub-room source to the target
component, depending on
MAIN ROOM/SUB ROOM (LEARN/TRANSMIT) selector
setting on the remote control.
• When you select a new source on the receiver or on the remote
control supplied for this receiver either for
the main room or sub-
room, the newly selected component begins playing immediately,
and the previously selected source continues playing without
sound for a few seconds.
Note:
If the source changes from an analog source, for which Line Direct
(see page 25) is activated, to a digital source, muting time* will be a
little longer.
* The period during which the receiver changes the source
mechanically. No sound comes out during this period.
PLAY
L
ANALOG
SPEAKERS
VOLUME
1
SUBWFR
R
dB
SPEAKERS
VOLUME
SUB ROOM
1
dB
CD player
CD recorder
Cassette deck
or
MD recorder
RX-DP10VBK
Turntable
IMPORTANT:
Check to see if the following before or while using the buttons and
controls.
For the main room operations:
The MAIN ROOM ON/OFF lamp on the unit is lit.
For the sub-room operations:
The SUB ROOM ON/OFF lamp on the unit is lit.
• When using the unit:
–For the main room operations: “SUB ROOM” is not shown in main
display.
–For the sub-room operations: “SUB ROOM” is shown in the main
display.
–Press DOOR DOWN to use the buttons inside the
front door.
To close the front door, press DOOR UP.
• When using the remote control:
When operating the receiver using the remote control, the
display on the unit always shows the main room source
information though you are operating it for the sub-room
source.
–Set the MAIN ROOM/SUB ROOM (LEARN/TRANSMIT) selector
to “MAIN ROOM” or “SUB ROOM” correctly.
–Check the indication shown on the remote’s display when you
press a button—this indicates the remote control operation mode
together with multi-room operation mode (either MAIN ROOM or
SUB ROOM) for a while (10 or 5 seconds).
DOOR
DOWN
SUB ROOM
TRANSMITLEARN
MAIN ROOM
SUB ROOM
TRANSMITLEARN
MAIN ROOM
EN54-60_RX-DP10VBK[J]_f 01.6.19, 11:39 AM54