Filter
Top Products
TMS320C6202
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SPRS072B – AUGUST 1998 – REVISED AUGUST 1999
66
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443
MULTICHANNEL BUFFERED SERIAL PORT TIMING (CONTINUED)
timing requirements for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 1
†‡
(see Figure 44)
NO.
’C6202-200
’C6202-233
’C6202-250
UNIT
NO
.
MASTER SLAVE
UNIT
MIN MAX MIN MAX
4 t
su(DRV-CKXH)
Setup time, DR valid before CLKX high 12 2 – 3P ns
5 t
h(CKXH-DRV)
Hold time, DR valid after CLKX high 4 5 + 6P ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
‡
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics for McBSP as SPI master or slave: CLKSTP = 10b, CLKXP = 1
†‡
(see Figure 44)
NO.
PARAMETER
’C6202-200
’C6202-233
’C6202-250
UNIT
NO
.
PARAMETER
MASTER
§
SLAVE
UNIT
MIN MAX MIN MAX
1 t
h(CKXH-FXL)
Hold time, FSX low after CLKX high
¶
T – 2 T + 3 ns
2 t
d(FXL-CKXL)
Delay time, FSX low to CLKX low
#
H – 2 H + 3 ns
3 t
d(CKXL-DXV)
Delay time, CLKX low to DX valid –2 4 3P + 4 5P + 17 ns
6 t
dis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit from
CLKX high
H – 2 H + 3 ns
7 t
dis(FXH-DXHZ)
Disable time, DX high impedance following last data bit from
FSX high
P + 3 3P + 17 ns
8 t
d(FXL-DXV)
Delay time, FSX low to DX valid 2P + 2 4P + 17 ns
†
P = 1/CPU clock frequency in ns. For example, when running parts at 250 MHz, use P = 4 ns.
‡
For all SPI slave modes, CLKG is programmed as 1/2 of the CPU clock by setting CLKSM = CLKGDV = 1.
§
S = sample rate generator input clock = P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
¶
FSRP = FSXP = 1. As a SPI master, FSX is inverted to provide active-low slave-enable output. As a slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for slave McBSP
#
FSX should be low before the rising edge of clock to enable slave devices and then begin a SPI transfer at the rising edge of the master clock
(CLKX).
ADVANCE INFORMATION