Filter
Top Products
109
Setup Menu
Listening Mode Setup
—Continued
g. Surr Bk Speaker
This option configures the surround back speakers to
use when playing the source in the DTS listening mode.
Select the speaker terminals to which the speakers you
want to use are connected. This setting can be made
when the “(Speaker B) Surr Back” is set to “Main A” in
the Speaker Configuration sub-menu. However, when
the “(Speaker A) Surr Back” is set to “BTL for Front,”
“Bi-Amp for Front,” or “Not Used,” this setting will not
be displayed.
• When the impedance setting for “Surr L/R A” or “Surr
L/R B” in the Speaker Impedance sub-menu is set to
“6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
• When the settings for “(Speaker A) Surr Back” and
“(Speaker B) Surr Back” in the Speaker
Configuration sub-menu differ, the available options
will be “A” and “B.”
A (Default):
Outputs the source from the speakers
connected to the SURR BACK L/R SPEAKERS A
terminals.
B:
Outputs the source from the speakers connected to
the SURR BACK L/R SPEAKERS B terminals.
A+B:
Outputs the source from the speakers connected
to the SURR BACK L/R SPEAKERS A and SURR
BACK L/R SPEAKERS B terminals.
h. Subwoofer
This option configures the subwoofer to use when
playing the source in the DTS listening mode. Select the
terminal to which the subwoofer you want to use is
connected. This setting can be made when the
“(Speaker A) Subwoofer” is set to an option other than
“Not Used” in the Speaker Configuration sub-menu.
However, when the “(Speaker B) Subwoofer” is set to
an option other than “Main A” in the Speaker
Configuration sub-menu, the available options will be
“A” or “Not Used.”
A (Default):
Outputs the source only from the
subwoofer connected to the SUBWOOFER PRE OUT
A terminal.
B:
Outputs the source only from the subwoofer
connected to the SUBWOOFER PRE OUT B terminal.
A+B:
Outputs the source from the subwoofers
connected to the SUBWOOFER PRE OUT A and
SUBWOOFER PRE OUT B terminals.
Not Used:
No subwoofers are used for playback.
This sub-menu allows you to configure the audio effect
and playback options when you play a source in the
AAC listening mode.
a. LFE Level
This option allows you to set the bass level for the AAC
listening mode. The LFE level setting made here will be
applied to all of the AAC input signals. The available
settings are –
∞
dB, –20 dB, –10 dB, and 0 dB. The option
defaults to “0.” This option can also be set for Zone 2.
b. SB Mode (5ch)
Selects the enhancement mode for playback when you
play a 5.1ch source as a 6.1 or higher channel source
through the DTR-10.5. The surround back setting you
select here will be applied to the AAC input signal “*/
2.”
• When the “(Speaker A) Surr Back” is set to “BTL for
Front,” “Bi-Amp for Front,” or “Not Used” in the
Speaker Configuration sub-menu, this option will not
be displayed.
Dolby EX:
Plays a 5.1ch source as a 6.1 or higher
channel source using the Dolby Digital EX mode.
PLIIx Movie (Default):
Plays a 5.1ch source as a 6.1
or higher channel source using the Dolby Pro Logic IIx
Movie mode.
• When you set the (Speaker A) Surr Back setting to
“Main A 1ch (SBL)” in the Speaker Configuration
sub-menu, you cannot select “PLIIx Movie.”
PLIIx Music:
Plays a 5.1ch source as a 6.1 or higher
channel source using the Dolby Pro Logic IIx Music
mode.
NEO:6:
Plays a 5.1ch source as a 6.1 or higher channel
source using the DTS NEO:6 mode.
Off:
Plays an original 5.1ch source as it is.
c. Re-EQ
This option allows you to configure whether the Re-EQ
effect is applied or not. Use this effect when you do not
want to overemphasize the treble sound.
Off (Default):
The effect is not applied.
On:
Adjusts the soundtrack in which the treble is
overemphasized, so that the sound is optimized for
home theater.
d. Front Speaker
This option configures the front speakers to use when
playing the source in the AAC listening mode. Select
the speaker terminals to which the speakers you want to
use are connected. This setting can be made when the
“(Speaker B) Front L/R” is set to “Main A” in the
Speaker Configuration sub-menu.
• When the impedance setting for “Front L/R A” or
“Front L/R B” in the Speaker Impedance sub-menu is
set to “6 ohms” or “4 ohms,” the available options will
be “A” and “B.”
A (Default):
Outputs the source from the speakers
connected to the FRONT L/R SPEAKERS A terminals.
B:
Outputs the source from the speakers connected to
the FRONT L/R SPEAKERS B terminals.
A+B:
Outputs the source from the speakers connected
to the FRONT L/R SPEAKERS A and FRONT L/R
SPEAKERS B terminals. Note that this option is not
available when the front speakers are in Bi-amp or in
BTL configuration.
AAC Setup Sub-menu