Filter
Top Products
106
Listening Mode Setup
—Continued
g. Surr Bk Speaker
This option configures the surround back speakers to
use when the DTR-10.5 plays a Super Audio CD. Select
the speaker terminals to which the speakers you want to
use are connected. This setting can be made when the
“(Speaker B) Surr Back” is set to “Main A” in the
Speaker Configuration sub-menu. However, when the
“(Speaker A) Surr Back” is set to “BTL for Front,” “Bi-
Amp for Front,” or “Not Used,” this setting will not be
displayed.
• When the impedance setting for “Surr L/R A” or “Surr
L/R B” in the Speaker Impedance sub-menu is set to
“6 ohms” or “4 ohms,” the available options will be
“A” and “B.”
• When the settings for “(Speaker A) Surr Back” and
“(Speaker B) Surr Back” in the Speaker Configuration
sub-menu differ, the available options will be “A” and
“B.”
A (Default):
Outputs the source from the speakers
connected to the SURR BACK L/R SPEAKERS A
terminals.
B:
Outputs the source from the speakers connected to
the SURR BACK L/R SPEAKERS B terminals.
A+B:
Outputs the source from the speakers connected
to the SURR BACK L/R SPEAKERS A and SURR
BACK L/R SPEAKERS B terminals.
h. Subwoofer
This option configures the subwoofer to use when the
DTR-10.5 plays a Super Audio CD.
Select the terminal to which the subwoofer you want to
use is connected. This setting can be made when the
“(Speaker A) Subwoofer” is set to an option other than
“Not Used” in the Speaker Configuration sub-menu.
However, when the “(Speaker B) Subwoofer” is set to
an option other than “Main A” in the Speaker
Configuration sub-menu, the available options will be
“A” or “Not Used.”
A (Default):
Outputs the source only from the
subwoofer connected to the SUBWOOFER PRE OUT
A terminal.
B:
Outputs the source only from the subwoofer
connected to the SUBWOOFER PRE OUT B terminal.
A+B:
Outputs the source from the subwoofers
connected to the SUBWOOFER PRE OUT A and
SUBWOOFER PRE OUT B terminals.
Not Used:
No subwoofers are used for playback.
This sub-menu allows you to configure the audio effect
and playback options when you play a source in the
Dolby Digital listening mode.
a. LFE Level
This option allows you to set the bass level for the Dolby
Digital listening mode. The LFE level setting made here
will be applied to all of the Dolby Digital input signals.
The available settings are –
∞
dB, –20 dB, –10 dB, and 0
dB. The option defaults to “0.” This option can also be
set for Zone 2.
b. Late Night
This option allows you to set how the Late Night function
works (See page 57). The setting you select here will be
applied to all of the Dolby Digital input signals. Note that
the Late Night setting will not be retained and will return
to “Off” after the DTR-10.5 enters the standby state. This
option can also be set for Zone 2.
Off:
Disables the Late Night function.
Low:
Narrows the volume range.
High:
Narrows the volume range more than the “Low”
setting.
c. Dolby EX
This option configures the Dolby EX effect when
playing the source in the Dolby Digital listening mode.
Auto:
Automatically plays a source using the Dolby EX
mode when the source contains the Dolby Digital EX
identification signal. When this signal is not contained,
the setting of “SB Mode (5ch)” is applied.
Manual:
The setting of “SB Mode (5ch)” is applied
regardless of the Dolby Digital EX identification signal.
d. SB Mode (5ch)
This option allows you to select the enhancement mode
for playback when you play a 5.1ch source as a 6.1 or
higher channel source through the DTR-10.5. The
surround back setting you select here will be applied to
the Dolby Digital input signal “*/2.”
• When the “(Speaker A) Surr Back” is set to “BTL for
Front,” “Bi-Amp for Front,” or “Not Used” in the
Speaker Configuration sub-menu, this option will not
be displayed.
Dolby EX:
Plays a 5.1ch source as a 6.1 or higher
channel source using the Dolby Digital EX mode.
PLIIx Movie (Default):
Plays a 5.1ch source as a 6.1
or higher channel source using the Dolby Pro Logic IIx
Movie mode.
• When you set the (Speaker A) Surr Back setting to
“Main A 1ch (SBL)” in the Speaker Configuration
sub-menu, you cannot select “PLIIx Movie.”
PLIIx Music:
Plays a 5.1ch source as a 6.1 or higher
channel source using the Dolby Pro Logic IIx Music
mode.
NEO:6:
Plays a 5.1ch source as a 6.1 or higher channel
source using the DTS NEO:6 mode.
Off:
Plays an original 5.1ch source as it is.
e. Re-EQ
This option allows you to configure whether the Re-EQ
effect is applied or not. Use this effect when you do not
want to overemphasize the treble sound.
Off (Default):
The effect is not applied.
Dolby Digital Setup Sub-menu