Filter
Top Products
Getting Started Connections Settings Playback Remote ControlMulti-zone Information Troubleshooting SpecificationsSettings
Making Detailed Settings (Manual Setup)
Main remote control unit
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
Setting items Setting contents
Other
(Continued)
Party Start Level : Make settings for volume level when the Party Mode
is started.
Last : The same volume as set before the party mode was started.
– – – (0) : Always use the muting on condition when the Party Mode is
started.
–80dB ~ 18dB (1 ~ 99) : Start party mode with your preferred volume.
This can be set when “Party Mode Function“ is set to “ON“.
This is displayed from 0 to 99 when “Volume Display” (vpage 53) is
set to “Absolute”.
You can set to the upper limit set with “Volume Limit” (vpage 53) .
•
•
•
•
•
•
Network Status : Displays up to a maximum of 10 DENON products
connected on the same network.
Friendly Name / Model Name / Power ON/Standby / Select Source /
Volume Level / Party Mode status
“Network Status” is only displayed for DENON products supporting
the Network Status function.
•
Update Notification : Displays a notification message on the AVR-
4810CI’s GUI screen when the latest firmware is released with “Firmware
Update”. The notification message is displayed for about 20 seconds
when the power is turned on. Connect to broadband Internet (vpage
26) when using this function.
ON : Display update message.
OFF : Do not display update message.
When you press ENTER during display of the notification message, the
“Check for Update” screen is displayed. (Refer to page 56 for more
information on “Firmware Update”.)
Press RETURN to erase the notification message.
•
•
•
•
Upgrade Notification : Display a notification message on the AVR-
4810CI’s GUI screen when downloadable firmware is released with “Add
New Feature”. The notification message is displayed for about 20 seconds
when the power is turned on. Connect to broadband Internet (vpage 26)
when using this function.
ON : Display upgrade message.
OFF : Do not display upgrade message.
When you press ENTER during display of the notification message, the
“Add New Feature” screen is displayed. (Refer to page 56 for more
information on “Add New Feature”.)
Press RETURN to erase the notification message.
•
•
•
•
Setting items Setting contents
Rhapsody Account
Set or change Username
and Password (vpage 83
“Listening to Rhapsody“).
Username / Password
The types of characters that can be input are as shown below.
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GSymbolsH ! “ # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ˜
GNumbersH 0123456789 (Space)
You can change the character type when you press SEARCH on the main
remote control unit or MENU during character input.
The password may not contain underscores ( _ ).
•
•
Napster Account
Set or change Username
and Password (vpage 82
“Listening to Napster“).
Username / Password
The types of characters that can be input are as shown below.
GLower case charactersH abcdefghijklmnopqrstuvwxyz
GUpper case charactersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GSymbolsH ! “ # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ˜
GNumbersH 0123456789 (Space)
You can change the character type when you press SEARCH on the main
remote control unit or MENU during character input.
The password may not contain underscores ( _ ).
•
•
Network Information
Display network information.
Friendly Name / Network=Wired/Wireless / SSID /
DHCP= ON/OFF / IP Address / MAC Address