Filter
Top Products
87
Letting the Remote Controller Learn the Codes from Other Remote
Controllers—Continued
Notes:
• The remote controller codes for Onkyo compact disc
players, cassette tape decks, DVD players, and mini
disc recorder have already been programmed into
buttons on the remote controller. You may, however,
use these buttons to program the codes for other
remote controllers. If you wish to restore the Onkyo
preset codes after you program new codes, you must
first erase the new codes (See this page).
• The remote controller has 408 memory slots (8
modes × 51 buttons). Some remote controllers may
have more commands than can be remembered by the
remote controller. In such cases, it will be necessary
for you to determine which commands are more
important to you.
• If the SEND/LEARN indicator quickly flashes three
times and turns off, then the remote controller has
exited the programming mode because either you
have made a mistake during programming or a time-
out has occurred because no button was pressed.
Resume from Step 2.
• If you try to program beyond the learning capacity of
the remote controller, the SEND/LEARN indicator
flashes six times quickly, and the remote controller
exits the programming mode. Try programming
under a different MODE button.
• When you want to program a command to a button to
which you have already programmed a command, sim-
ply follow the same procedure given and the previous
programming for that button will be overwritten.
• The remote controller uses infrared rays to send its
commands, as do most other remote controllers.
Though most remote controller codes can be memo-
rized by the remote controller, be aware that some
remote controllers use systems that are quite different
from the remote controller and therefore may not be
able to be programmed.
• Some remote controllers have a single button that
performs multiple functions (for example, the func-
tion may change each time the button is pressed). If
this is the case, each function must be programmed to
a separate button on the remote controller.
• Once you have transferred the commands from the
other remote controller, refer to the instruction man-
ual that came with that product for instructions on
how to operate that product.
• Make sure both the remote controller and the other
remote controller have new batteries. If either of them
has batteries that are low, you may not be able to pro-
gram the commands of the other remote controller
properly into the remote controller.
Erasing the programmed command from one
button
You can only erase memorized commands and not preset ones.
Note:
If no button is pressed for more than 30 seconds during
the erasing procedure, the SEND/LEARN indicator
flashes three times quickly, and the remote controller
exits the erasing mode. Resume from Step 1.
Erasing all the commands programmed under a
MODE button
Notes:
• If no button is pressed for more than 30 seconds dur-
ing the erasing procedure, the SEND/LEARN indica-
tor flashes three times quickly and the remote
controller exits the erasing mode. Resume from Step 1.
• If you perform an invalid operation during erasing,
the SEND/LEARN indicator flashes three times
quickly, and the remote controller exits the erasing
mode. Resume from Step 1.
• If many commands have been programmed to the
MODE button, then the SEND/LEARN indicator
may remain lit for up to 20 seconds during Step 2.
This is not a malfunction.
1
Press and hold down the MODE button for
the command, press the ENTER/ZONE 2
button, and then release both buttons.
When you press the MODE button, the SEND/
LEARN indicator lights. When you press the
ENTER/ZONE 2 button, the lamp turns off. When
you release the buttons, the lamp lights again.
2
Press and release the button for the com-
mand you wish to erase.
When you press the button, the SEND/LEARN
indicator turns off. When you release the button,
the lamp lights again.
3
Press and release the same button again.
The SEND/LEARN lamp slowly flashes twice.
The memorized command is erased.
1
Press and hold down the desired MODE
button, press the ENTER/ZONE 2 button
twice, and then release both buttons.
When you press the MODE button, the SEND/
LEARN indicator lights. When you press the
ENTER/ZONE 2 button, the lamp turns off.
When you release the buttons, the lamp slowly
flashes twice and then lights again.
2
Press and release the same MODE button
again.
When you release the button, the SEND/LEARN
indicator slowly flashes twice. This erases all the
commands memorized to the MODE button.