Filter
Top Products
31
Selecting the Appropriate Setting for Your Connections—Continued
a. Surr Back/Zone 2
Zone 2: Select when connecting the speakers for the
remote zone (Zone 2) to the SURR BACK/ZONE 2
PRE OUT or SURR BACK/ZONE 2 SPEAKERS
terminals (for using the internal amplifier for Zone 2).
Surr Back (default): Select when not connecting
the speakers for the remote zone (Zone 2) to the
SURR BACK/ZONE 2 PRE OUT or SURR BACK/
ZONE 2 SPEAKERS terminals (for using the
internal amplifier for the surround back speakers).
Note:
The SURR BACK/ZONE 2 PRE OUT and SURR
BACK/ZONE 2 SPEAKER terminals
In order to have 7.1 channel playback in the main room,
you must set the Surr Back/Zone 2 setting to “Surr
Back.” When set to “Surr Back,” the surround back
signals are output from the SURR BACK/ZONE 2 PRE
OUT and SURR BACK/ZONE 2 SPEAKER terminals.
Connect the surround back speakers to the SURR
BACK/ZONE 2 SPEAKER terminals or to the speakers
terminals of the power amplifier connected to the SURR
BACK/ZONE 2 PRE OUT terminals.
When you are not using the surround back speakers in
the main room and are using the internal amplifier to
power the speakers for the remote zone (Zone 2), set the
Surr Back/Zone 2 setting to are “Zone 2.” When set to
“Zone 2,” the Zone 2 signals are output from the SURR
BACK/ZONE 2 PRE OUT and SURR BACK/ZONE 2
SPEAKER terminals. Connect the remote zone (Zone 2)
speakers to the SURR BACK/ZONE 2 SPEAKER
terminals or to the speaker terminals of the power
amplifier connected to the SURR BACK/ZONE 2 PRE
OUT terminals.
At this time, the main room is switched to 5.1 channel
playback mode, and therefore you cannot select the THX
Surround EX, Dolby Digital EX or DTS-ES, which
requires the surround back speakers.
Remote Setup Sub-menu
Use this sub-menu when you have a remote control
sensor connected to the IR IN terminal. The setting in
this sub-menu tells the TX-NR801/TX-NR801E
whether the remote control sensor is being used for
operation of the TX-NR801/TX-NR801E in the main
zone or the remote zone (Zone 2).
a. Position
Main: Select when you are using the remote control
sensor for operation with the remote controller in the
main zone.
Zone 2: Select when you are using the remote
control sensor for operation with the remote
controller in the remote zone (Zone 2).
TV Format Sub-menu
a. TV Format (For all models other than USA and
Canadian models)
When you want to reconfigure the settings conforming
to the television format used for the area where you use
the TX-NR801/TX-NR801E, use this sub-menu so that
no time is wasted on detection.
Auto: This is the default setting. When you leave
this setting unchanged, the television format is
detected and automatically set by the TX-NR801/
TX-NR801E.
PAL: Use this setting when you know that the televi-
sion format is PAL.
NTSC: Use this setting when you know that the tele-
vision format is NTSC.
AM Frequency Step Sub-menu
(Worldwide model Only)
This sub-menu only appears on the worldwide model.
The setting in this sub-menu determines the incremental
or decremental amount when adjusting the AM tuner
frequency. The initial setting is 9 kHz, and this needs
only to be changed if you are using the TX-NR801/
TX-NR801E in a 10 kHz region.
a. Frequency Step
9 kHz: Select when you use the TX-NR801/
TX-NR801E in North America.
10 kHz: Select when you use the TX-NR801/
TX-NR801E in other than USA and Canada.
0-3.Remote Setup
a.Position :Main
Quit:[SETUP]
0-4.TV Format
a.TV Format
:Auto
Quit:[SETUP]
0-5.AM Frequency Step
a.Frequency Step
:9 kHz
Quit:[SETUP]