Filter
Top Products
23
Connecting to Audio/Video Equipment—Continued
Using an RCA video connection cable, connect the
video output jack (composite) of the device to the
VIDEO 3 (or 4) VIDEO IN jack of the TX-NR801/
TX-NR801E. Or if the device has an S video output jack,
connect it to the VIDEO 3 (or 4) S VIDEO IN jack of the
TX-NR801/TX-NR801E using an S video connection
cable. Or if the device has component video outputs,
connect them to one of the banks of COMPONENT
VIDEO INPUT jacks on the TX-NR801/TX-NR801E.
On the initial settings of the TX-NR801/TX-NR801E,
the VIDEO 3 and 4 input sources are set for the
COMPONENT VIDEO INPUT 2 jacks.
If you connect the device to the COMPONENT VIDEO
INPUT 1 jacks, this must be changed at Setup Menu →
Input Setup → Video Setup → Component Video (See
page 38).
Using an RCA audio connection cable, connect the
audio output jack of the device to the VIDEO 3 (or 4)
AUDIO IN jacks of the TX-NR801/TX-NR801E. Make
sure that you properly connect the left channel to the L
jack and the right channel to the R jack.
When hooking up a TV with audio outputs, make sure
the TV’s audio output setting. You might have to go
through the TV’s menu and set the TV Fixed audio
output and then internal speakers off.
If the device has a digital output, connect it to either the
DIGITAL IN COAX jack or DIGITAL IN OPT jack of
the TX-NR801/TX-NR801E, depending on the type of
connector on the device.
On the initial settings of the TX-NR801/TX-NR801E,
the VIDEO 3 input source is set for digital input at
the OPT 3 jack.
If the digital connection is made at a different jack, this
must be changed at Setup Menu → Input Setup →
Digital Setup (See page 36).
On the initial settings of the TX-NR801/TX-NR801E,
the VIDEO 4 input source is not set for digital input. If
you are connecting a digital component, these settings
must be changed at Setup Menu → Input Setup →
Digital Setup (See page 36).
Using an RCA video connection cable, connect the
video output jack (composite) of the device to the
VIDEO 5 VIDEO jack of the TX-NR801/TX-NR801E.
Or if the device has an S video output jack, connect it to
the VIDEO 5 S VIDEO jack of the TX-NR801/
TX-NR801E using an S video connection cable.
Using an RCA audio connection cable, connect the
audio output jack of the device to the VIDEO 5 AUDIO
jacks of the TX-NR801/TX-NR801E. Make sure that
you properly connect the left channel to the L jack and
the right channel to the R jack.
If the device has an optical digital output, connect it to
the VIDEO 5 DIGITAL jack of the TX-NR801/
TX-NR801E.
The VIDEO 5 digital input is fixed to the OPTICAL
input on the front panel.
Using an RCA audio connection cable, connect the
output jacks of the compact disc player to the CD
AUDIO jacks of the TX-NR801/TX-NR801E. Make
sure that you properly connect the left channel to the L
jack and the right channel to the R jack.
If the compact disc player has a digital output, connect it
to either the DIGITAL IN COAX jack or DIGITAL IN
OPT jack of the TX-NR801/TX-NR801E, depending on
the type of connector on the compact disc player.
On the initial settings of the TX-NR801/TX-NR801E,
the CD input source is set for digital input at the OPT
1 jack.
If the digital connection is made to a different jack, this
must be changed at Setup Menu → Input Setup →
Digital Setup (See page 36).
Connecting Video Camera, etc.
(VIDEO 5 INPUT)
Connecting a Compact Disc Player
(CD)
R
L
AUDIO OUT VIDEO
OUT
S VIDEO
OUT
DIGITAL
OUT
R
L
R
L
Video camera/ Video
game (VIDEO 5 INPUT)
Front panel
AUDIO
VIDEO
S VIDEO
MONITOR
OUT
R
L
IN
IN
IN
IN
IN
ZONE 2
DVD
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
AUDIO
VIDEO
S VIDEO
COMPONENT
VIDEO
Y
P
B
PR
OUTPUT
INPUT 1
Y
P
B
PR
INPUT 2
Y
P
B
PR
R
L
OUT
OUT
OUT
PHONO
DIGITAL
IN
PRE OUT
DIGITAL
OUT
OPT
OPT
2
1
2
1
2
3
FRONT
SUB
SURR
R
L
AUDIO
R
L
CD
TAPE
R
L
AUDIO
1
3
GND
SURR
BACK/
ZONE 2
IN
OUT
COAX
R
L
MULTI
CH
INPUT
FRONT
SUB
SURR
SURR
BACK
CENTER
RL
R
L
AM
FM
75
CENTER
ANTENNA
IN
IN
CD
IN
RL
1
DIGITAL
IN
OPT
DIGITAL
OUT
OPT
AUDIO
RL
AUDIO OUT
CD player