Panasonic WJ-DR200 Stereo Receiver User Manual


 
DefaultWJ-FS616 Setup Menu
SYSTEM SETUP 2/2
SYSTEM SETUP 2/2
REC MODE SETUP
WJ-FS616 SETUP MENU
SYSTEM SETUP 1/2
ALARM SETUP
Item
VCR IN SELECT
REC/MULTI 2
SEQ TIMING-MLT
ALM SCHEDULE
ALM OUTPUT DUR
DYNAMIC REC
ALM REC MODE
RS-232C MODE
Parameter
VIDEO *1
REC OUTPUT
EXT *5
VIDEO
S-VIDEO *1 VIDEO
REC OUTPUT
MODE 9 (EXT1 or EXT4) *3 MODE 0
INT (TIME-ADJ)
ON OFF
2 SEC
ON *4 OFF
MODE 9 MODE 0
VCR *2 VCR
INT (TIME-AJD)
-9-
BNC Connector
Pin Plug
WJ-DR200
WJ-FS616
H
L
H
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A B
T
A B
R
G
N
D
G
N
D
RS485 TERM.
LINE
SELECT
CAMERA
SW IN
GENLOCK
IN (VS)
OFF ON 2 4
SPOT
REC OUT PLAY IN
MULTISCREEN
VCR CONTROL
RS232C
OUT I N
VIDEO S
VIDEO S
VIDEO S
VIDEOVIDEOVIDEO
REMOTE
ALARM/REMOTE
OUT
TERM.
OFF
INOUT
ON
SIGNAL
GND
DATA
CAMERA
IN
CAMERA
OUT
CAUTION
- FOR CONTINUED PROTECTION
Manufactured by Matushita Communication
Industrial Co. Ltd Yokohama Japan
- AFIN D' ASSURER UNE
ATTENTION
AGAINST FIRE HAZARD REPLACE ONLY WITH
SAME TYPE FUSE
PROTECTION PERMANENTE CONTRE LES RISQUES
D' INCENDIE REPLACER UNIQUEMENT PAR UN
FUSIBLE DE MEME TYPE
POWER 120V AC 60 Hz 38W
VIDEO OUT 1V [ p-p ] 75
FOR COMMERCIAL USE ONLY
Made In Japan
SIGNAL GND
120V AC 60Hz
OFF
125V 4 A
POWER
ON
GND
SENSOR IN
ALARM IN
ALARM RESET IN
SERIES REC IN
TIME ADJUST IN
GND
ALARM OUT
ALARM RECOVER OUT
ALARM REC
REC
DISC
BUZZER OUT
SYSTEM ERROR OUT
THERMAL ERROR OUT
TIME ADJUST OUT
SERIES REC OUT
LED
MONITOR
CAMERA SW OUT
AUDIO
PARALELL CONTROL
SERIAL CONTROL
IN
OUT
S-VIDEO
OUT
S-VIDEO
VIDEO OUT
VIDEO IN
BA
SER.
NO.
6ZA00001
OUTPUT LEVEL
H
L
OUTPUT LEVEL
Alarm
Output Level
Selector
SW1
OFF
SW1: Recording
Output
*1. Select VIDEO or S-VIDEO according to the connection.
VIDEO: Select this parameter when the BNC connector is used for the connection.
S-VIDEO: Select this parameter when the S- VIDEO connector is used for the connection.
Monitoring the playback picture from the MULTISCREEN OUT connector or the SPOT connector is not available.
*2. Connect only when WJ-DR200 is controlled by Video Multiplexer WJ-FS616. (Refer connection of the cable to qualified
service personnel or system installers.)
You need to set the communication parameters (DATA BIT, PARITY, etc.) on both the WJ-DR200 and the WJ-FS616.
*3. This value applies to EXT 1. For EXT 4, set the parameter to 0.20 sec. or more.
*4. Set this parameter to change the recording rate automatically when an alarm signal is received.
*5. Set the recording time when alarm time lapse recording is required.
WJ-FS616 System Setup