Filter
Top Products
60
Operating Other Manufacturers’ Video Equipment
To change the transmittable signals for
operating another manufacturer’s TV
1. Set the remote control mode to “AUDIO/TV/
VCR.”
2. Press and hold TV/CATV/DBS POWER.
3. Press TV/DBS.
4. Enter manufacturer’s code (two digits) using
buttons 1–9, and 0.
See the list on page 62 to find the code.
Examples: For a JVC product, press 2, 8.
For a Sanyo product, press 2, 5.
5. Release TV/CATV/DBS POWER.
The following buttons can be used for operating the TV (with
the remote control mode selector set to “AUDIO/TV/VCR”):
TV POWER Turns on and off the TV.
TV VOL +/– Adjusts the volume.
TV/VIDEO Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the remote control mode selector
set to “AUDIO/TV/VCR”), you can perform the following
operations on a TV:
CHANNEL +/– Changes the channels.
1 – 10, 0, 100+ (+10) Selects the channels.
The 100+ (+10) button will function
as the ENTER button if your TV
requires pressing ENTER after
selecting a channel number.
6. Try to operate your TV by pressing TV/CATV/
DBS POWER.
When your TV turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
To change the transmittable signals for
operating a CATV converter or DBS tuner
1. Set the remote control mode to “CATV/DBS.”
2. Press and hold TV/CATV/DBS POWER.
3. Press TV/DBS.
4. Enter manufacturer’s code (two digits) using
buttons 1 – 9, and 0.
See the list on page 62 to find the code.
Examples: For a JVC product, press 5, 7.
For a Sony product, press 6, 5.
This remote control supplied with the receiver can transmit control
signals for other manufacturers’ VCRs, TVs, CATV converters,
DBS tuners, and DVD players. By changing the transmittable
signals from preset ones to the other manufacturers’, you can
operate the other manufacturer’s components using this remote
control.
When operating the other manufacturers’ components, refer also to
the manuals supplied with them. To operate these components with
the remote control, first you need to set the manufacturer’s code
each for VCR, TV, CATV converter, DBS tuner, and DVD player.
RM-SRX9000J REMOTE CONTROL
CONTROL
CHANNEL VOLUMETV VOL
TUNING
STOP PAUSE
FF/
/REW
VCR 1
TV/VIDEO
TAPE/MD
MUTING
REC
PLAY
DOWN UP
DVD DVD MUILTI CD TAPE/MD
TV/DBS VIDEO PHONO FM/AM
VCR 1
CDR/VCR 2
ANALOG/DIGITAL
SURROUND CNTR TONE
CENTER
SURROUND
REAR TONE
REAR-L
CD-DISC
MODE
ON/OFF
SEA MODE REAR-R
SOUND
TEST
SUBWOOFER
RETURN FM MODE
SET
MENU
AUDIO/
TV/VCR
EXIT
TEXT
DISPLAY
SLEEP
123
456
7
/P 89
10
0
+10
100+
CATV/DBS
MENUMENU
ENTERENTER
STANDBY ON
TV/CATV/DBS
VCR 1
POWER POWER
MAIN ROOM
SUB ROOM
SUB
ROOM
MAIN
ROOM
ON/OFF ON/OFF
AUDIO/
TV/VCR
CATV/DBS
Check to see if the remote
control mode selector is set
to the correct position.
To operate the audio
system, TVs, and VCRs,
set it to “AUDIO/TV/VCR.”
To operate the CATV
converter, DBS tuner, and
DVD player, set it to “CATV/
DBS.”
IMPORTANT:
• To operate the video component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
– Place the IR signal transmitter so that it is aimed at the remote
sensor on the target video component(s).
– The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
– The IR signal transmitter can send signals at a distance of 10 feet
(3 m).
EN54_65.RX-9000V[J]/f 00.2.15, 3:51 PM60