Filter
Top Products
E-32
Update process
When this unit is turned on, the Internet connection starts
automatically.
“Accessing...” blinks on the screen.
The current version of this unit software and the latest version
of the update file on the network are displayed when latest
version of rmware has been found.
To update this unit software with update le, select “Yes”, and
go to step 2.
Latest version of firmware has been found.
Firmware update is available.
Proceed with update?
If “Yes” will be selected, version update will start.
Current Version :
Latest Version :
xxxxxxxxxx
yyyyyyyyyy
Yes
No
If the latest firmware version has been already updated,
nothing is displayed on the screen.
Press ENTER to start updating.
Downloading latest firmware…
Version : yyyyyyyyyy
30%
When the software is successfully updated, a screen is displayed
indicating that the update process is completed.
If the update has failed, an error message appears.
Retry the update after checking if the broadband Internet
connection (page 11) and communication settings (pages 29–
30) are performed properly.
Press ON/STAND-BY to turn off the unit before using again.
Manual Update from Network
This function allows you to perform the update operation by
accessing an Internet connection manually to check if there is a new
rmware version.
Notes:
Make sure that the LAN cable is connected to this unit.
Make sure to perform the communication settings. (See pages 29
–30.)
It may take time to access and download the update depending
on the Internet connection and other factors.
�
●
●
●
2�
3�
●
4�
●
●
●
Caution:
Do not remove the LAN cable or unplug the AC power lead while
downloading or updating software.
Press / to select “Settings”, then press or ENTER.
Press / to select “Software Update Settings”, then press
or ENTER.
Press / to select “Manual Update”, then press or ENTER.
Press / to select “Network”, then press ENTER.
During access to the network and checking the latest version of
rmware, “Accessing” blinks.
The current version of this unit software and the latest version
of the update file on the network are displayed when latest
version of rmware has been found.
To update this unit software with update le, select “Yes”, and
go to step 6.
Latest version of firmware has been found.
Firmware update is available.
Proceed with update?
If “Yes” will be selected, version update will start.
Current Version :
Latest Version :
xxxxxxxxxx
yyyyyyyyyy
Yes
No
If the Internet connection has failed, an error message appears.
Retry the update after checking if the broadband Internet
connection (page 11) and communication settings (pages 29–
30) are performed properly.
Press ENTER to start updating.
●
�
2�
3�
4�
5�
●
●
6�
Downloading latest firmware…
Version : yyyyyyyyyy
30%
When the software is successfully updated, a screen is displayed
indicating that the update process is completed.
If the update has failed, an error message appears.
Retry the update after checking if the broadband Internet
connection (page 11) and communication settings (pages 29–
30) are performed properly.
Press ON/STAND-BY to turn off the unit.
Manual Update from USB memory device
This function allows software updates by inserting a USB memory
device with the update le into the USB1 terminal on this unit.
When a software update is performed, the software update data
must be written onto the USB memory device in advance using a
PC.
The USB memory device must be clear of all les except software
update data to allow new software uploading.
To check for the availability of a software update, visit www.sharp.de
When software update data is released, copy the data onto a
USB memory device after downloading it to a PC.
For methods such as downloading and copying to a USB memory
device, carefully read the description shown on the website
before performing the operation.
Notes:
Only USB memory devices formatted with FAT 32/16 are
compatible.
When formatting a USB memory device using a PC, perform the
following settings.
Format File System: FAT32
Allocation Unit Size: Default Allocation Size
Do not extract the rmware update le to any folders other than
the root directory on the USB memory device. The firmware
update le must be only one le directly in the root directory.
7�
●
8�
●
●
●
●
●
●
Settings (continued)