Sanyo PLC-WXL46 Home Theater System User Manual


  Open as PDF
of 68
 
57
Picture is not bri�ht enou�h.
– Check if "Contrast" or "Brightness" are adjusted properly (see Check if "Contrast" or "Brightness" are adjusted properly (seeCheckif"Contrast"or"Brightness"areadjustedproperly(see(see
pages31, 38).,38).38)..
– Check if "Image level" is selected properly (see pages 30, 37). Check if "Image level" is selected properly (see pages 30, 37).Checkif"Imagelevel"isselectedproperly(see pages 30, 37).(seepages30, 37).,37).37)..
– Check the LAMP REPLACE indicator. If it lights, the end of lamp Check the LAMP REPLACE indicator. If it lights, the end of lampChecktheLAMPREPLACEindicator.Ifitlights,theendoflamp
lifeisapproaching.Replacethelampwithanewonepromptly
(seepages54-55, 61).,61).61)..
– Check the Lamp control function (see pages 24, 46). Check the Lamp control function (see pages 24, 46).ChecktheLampcontrolfunction(see pages 24, 46).(seepages24,46).
The color is stran�e.
– Check theInputsignal, colorsystem,videosystem, orcomputer
systemmode.
– AdjusttheImagelevelproperly(seepages31, 38).,38).38).
Ima�e is Left/Ri�ht reversed.
Ima�e is Top/Bottom reversed.
– ChecktheCeiling/Rearfunction(seepage44).
– ChecktheCeilingfunction(seepage44).
The ima�e is distorted or runs off.
– Check the PC Adjustment menu or Screen menu and adjust them Check the PC Adjustment menu or Screen menu and adjust themCheckthePCAdjustmentmenuorScreenmenuandadjustthem
(seepages26-29,32-33,40).
No sound
– Checktheaudiocableconnectionfromaudioinputsource.
– Adjusttheaudiosource.
– PresstheVolume+button(seepage23).
– PresstheMutebutton(seepage23).
– When the AUDIO OUT is plugged in, the projector's built-inWhentheAUDIOOUTispluggedin,theprojector'sbuilt-in
speakerisnotavailable.
– Is the image projected?Youwill hear the sound only when the
imageisprojected.
Some displays are not seen durin�
the operation.
– ChecktheDisplayfunction(seepage41).
Auto PC adjustment function does
not work.
– Check the Input signal. Auto PC Adjustment function can not work Check the Input signal. Auto PC Adjustment function can not workChecktheInputsignal.AutoPCAdjustmentfunctioncannotwork
when480p,575p,720p,480i,575i,1035i,or1080iisselected(see
page27).
The settin� does not remain after
turnin� off power.
– Make sure you selected “Store” after adjusting settings. Some Make sure you selected “Store” after adjusting settings. SomeMakesureyouselected“Store”afteradjustingsettings.Some
settingscannotbestoredifnotregisteredwith“Store.”
Power mana�ement function does
not work.
– Power management function cannot work while "Freeze" or "NoPower management function cannotworkwhile"Freeze" or"No
Show"functionisrunning..
Ima�e disappears automatically
– Check the power management function in the Setting. The powerCheckthepowermanagementfunctionintheSetting.Thepower
managementissetto“On”atthefactory.
Capture function does not work. – Check the connection and the Input signal to see if there is signal.ChecktheconnectionandtheInputsignaltoseeifthereissignal.
The Remote Control does not work.
– Checkthebatteries.
– Makesurenoobstructionisbetweentheprojectorandtheremote
control.
– Makesureyouarenottoofarfromtheprojectorwhenusingthe
remotecontrol.Maximumoperatingrangeis16.4’(5m).
– Makesurethecodeoftheremotecontrolisconformedtothatof
theprojector(seepage46).
– UnlocktheKeylockfunctionfortheremotecontrol(seepage47).
The top control does not work
– Unlock the Keylockfunction for thetop controlof the projector
(seepage47).
Appendix
 previous next