44
ADVANCED FUNCTIONS
NOTE: Use caution when programming complicated activities.
It isn’t possible to program a pause or delay before sending
commands after Power On, and the component may not be
ready to respond to commands immediately after powering on.
To program, or “record” an activity, follow these steps:
1. To enter Program mode, simultaneously press and hold the Activity
Button and the Alphanumeric Key or AVR Power On or Off Button
to which the activity will be assigned.
2. Press the Source Selector (or Setup Button) for each device
before you enter individual commands. This step counts as one
of the 19 commands allowed for each activity.
3. For Power On, press the AVR or Device Power On Button.
4. Press the AVR or Device Power Off Button for Power Off.
5. Press the Activity Button to end the programming process, and
the last Source Selector (or the Setup Button) will flash three
times.
It isn’t possible to “edit” a command within an activity. To erase the
activity:
1. Press and hold the Activity Button and the Alphanumeric Key or
AVR Power On or Off Button until the Source Selector or Setup
Button lights.
2. Press the Activity Button to erase the activity.
To execute an activity, press the Activity Button, then press the
Alphanumeric Key (or the AVR Power On or Off Button) for the
Activity.
Resetting the Remote
To reset the remote to its factory defaults, simultaneously press and
hold the TV Source Selector and the “0” Alphanumeric Key. When
the TV Button relights, enter the code “333”. When the TV Button
goes out, and all of the Source Selectors flash, the remote control
will be reset.
PROCESSOR RESET
If the unit behaves erratically after a power surge, first turn off
the Main Power Switch and unplug the AC power cord for at least
3 minutes. Plug the cord back in and turn the receiver on. If this
doesn’t help, reset the AVR.
NOTE: A system reset erases all user configurations, includ-
ing video resolution, speaker and level settings, and tuner
presets. After a reset, reenter all of these settings from your
notes in the appendix worksheets.
To reset the AVR 2600, place it in Standby mode (press the front-
panel Standby/On Switch so that the Power Indicator turns amber).
Then press and hold the front-panel OK Button for at least 5 seconds
until the RESET message appears.
If the receiver does not function correctly ofter a processor reset,
contact an authorized Harman Kardon service center for assistance.
Authorized service centers may be located by visiting the Web site
at www.harmankardon.com.
NOTE: After performing a system reset, wait at least 1 minute
before pressing any Source Selectors.
MEMORY
If the AVR 2600 is unplugged or experiences a power outage, it will
retain user settings for up to four weeks. Use caution when pro-
gramming complicated activities.
It isn’t possible to program a pause or delay before sending com-
mands after Power On, and the component may not be ready to
respond to commands immediately after powering on.
To program, or “record” an activity, follow these steps:
1. To enter Program mode, simultaneously press and hold the
Activity Button and the Alphanumeric Key or AVR Power On
Button to which the activity will be assigned.
2. Press the Source Selector (or AVR Settings Button) for each
device before you enter individual commands. This step counts
as one of
the 19 commands allowed for each activity.
3. For Power On, press the AVR or Device Power On Button.
4. Press the AVR or Device Power Off Button for Power Off.
5. Press the Activity Button to end the programming process, and
the last Source Selector (or the AVR Settings Button) will flash
three times.
It isn’t possible to “edit” a command within an activity. To erase the
activity:
1. Press and hold the Activity Button and the Alphanumeric Key or
AVR Power On Button until the Source Selector or AVR Settings
Button lights.
2. Press the Activity Button to erase the activity.
To execute an activity, press the Activity Button, then press the
Alphanumeric Key (or the AVR Power On Button) for the Activity.
Learning
If you have programmed a product’s codes into the remote and find
that some functions are missing, the AVR 3550HD remote may
“learn” individual codes from the product’s original remote. See
page 28.
Resetting the Remote
To reset the remote to its factory defaults, simultaneously press and
hold the TV Source Selector and the “0” Alphanumeric Key. When
the TV Button re-lights, enter the code “333”. When the TV Button
goes
out, and all of the Source Selectors flash, the remote will be reset.
0142CSK - HK AVR 2600 OM Inlay_ENG_v2.qxp:HKP1477AVR245om.v2.qxd 26/05/09 10:36 Side 44