Filter
Top Products
72
Using the macro function
What is the macro function?
A macro function enables you to program a series of button
operations (up to 16) on the remote controller into a single button.
The series of operations are then called a macro. For example, to
play a compact disc player connected to the DTR-6.4/5.4 normally,
you must perform the following steps:
1. Press the RCVR Mode button.
2. Press the On button.
3. Press the CD (Input Selector) button.
4. Press the CD Mode button.
5. Press the playback ( ) button.
By using the macro function, you can perform the above five
operations by only pressing one button.
Tips:
• If you erase or change the command of a button programmed in
the macro, that operation of that button will no longer work in
the macro. In this case, it will be necessary for you to reprogram
the macro in order to avoid incorrect operation.
• The codes programmed into the macro will be transmitted at an
interval of 0.5 seconds. However, some devices may not be able
to complete one operation in 0.5 seconds and may miss the next
code. In this case, after pressing one operation button, you can
press the same Mode button again before pressing the next
operation button to add another 0.5 seconds between the two
operations.
--
/
---
123
456
+
10 0
789
Audio Sel
Muting
Angle
Subtitle
TV
/
VCR
Random
Audio Adjust
Enter
Search
Input Selector
Dimmer
Zone 2
Display
SURR
THX
StereoDirect
All ST
VOL
C
H
Disc
Pure A
Rec
DSP DSP Re
-
EQ
Level
AM
V
1
DVD
V
3
V
4
V
5
C
D
V
2
P
H
TAP TUN
RC
-
534M
Macro 1 Macro 2
CD
(Input
Selector)
On
CD Mode
RCVR Mode
Send/Learn
indicator
Mode buttons
(CD playback)
With the macro function, you can program a series of button
operations as a macro into the Macro button so the macro can be
executed with just one touch. Note that for the macro function, only
one macro can be programmed. For example, to program the macro
described above on this page for the Macro button, perform the
steps given below.
1. Press and hold down any one of the seven Mode
buttons, press the Macro 1 (or 2) button, and then
release both buttons.
When you press the Mode button, it lights and the Send/Learn
indicator lights. When you press the Macro 1 (or 2) button, the
indicator turns off. When you release the buttons, the indicator
flashes briefly and then lights again.
2. Press the operation buttons you wish to program in
order (in this case, press RCVR Mode → On → CD
(Input Selector) → CD Mode → playback ( ) button).
When you press each button, the Send/Learn indicator turns off.
When you release the button, the indicator lights.
3. Press the Macro 1 (or 2) button to complete the
procedure.
The Send/Learn indicator slowly flashes twice.
4. Check to see if the macro has been properly
programmed.
Notes:
• You may program up to 16 button operations into the macro
function. If you try to program a 17th operation, it will be
ignored, and programming is stopped.
• If the Send/Learn indicator quickly flashes three times and turns
off, then the remote controller has exited the programming
mode because either you have made a mistake during
programming or a time-out has occurred because no button has
been pressed. Resume from Step 1.
Perform the procedure below to execute the macro that you have
programmed into the remote controller. After programming the
macro, you should always run it at least once to make sure that it
has been programmed properly.
Point the remote controller at the DTR-6.4/5.4 and press
the Macro 1 (or 2) button.
It may take a while for the macro to finish transmitting, so be sure to
continue pointing the remote controller at the device until the Send/
Learn indicator turns off.
Programming the macro
Executing the macro