Filter
Top Products
39
Enjoying music or videos with the DTR-6.4/5.4
--
/
---
123
456
+
10 0
789
Audio Sel
Muting
Angle
Subtitle
TV
/
VCR
Random
Audio Adjust
Enter
Search
Input Selector
Dimmer
Zone 2
Display
SURR
THX
StereoDirect
All ST
VOL
C
H
Disc
Pure A
Rec
DSP DSP Re
-
EQ
Level
AM
V
1
DVD
V
3
V
4
V
5
C
D
V
2
P
H
TAP TUN
RC
-
534M
Audio Selector
Audio Sel
Preset
/
Cursor
/
Press the Audio Selector button on the front panel (or Audio Sel
button on the remote controller) to change the audio mode. Each
time the button is pressed, the mode changes from “Auto” →
“Multich” (only if DVD is selected as the input source) → “Analog”
and back to “Auto.”
Auto (automatic detection): With this setting, the DTR-6.4/5.4
automatically detects whether the input signal is digital or analog.
When a digital signal is not input, then the analog signal is played.
This setting only appears if a digital input is selected for the Digital
Input setting at “Input Setup” → “Digital Input” (see page 34).
Multich (Multichannel): Select this setting to play back the multi-
channel input from a DVD player with a 5.1-channel input port.
Analog: Select this setting to play back the input from a source
component connected to analog audio input jacks. With this setting,
even if a digital signal is input from the same component, only the
analog signal will be output.
Selecting the setting mode with the Cursor / button
while “Auto” appears
Auto: The digital signal suitable for the input signal will be
preceded for playback. When there is no digital signal input, analog
signal will be played.
DTS: Select this if you play DTS-formatted CD in “Auto” mode
and hear noise during fast-forward or rewind operation. Non-DTS
sound input will not be output.
PCM: Select this if you hear sound gap between PCM tracks such
as ones on CD in “Auto” mode. Non-PCM sound input will not be
output.
Notes:
• When you play DTS-formatted CD or LD, be sure to select
“Auto” or “DTS.” If you select “PCM,” noise will be heard.
• If a DTS signal is not input when “DTS” is selected, the DTR-
6.4/5.4 will not automatically switch to analog output even
though “Auto” is selected with the Audio Selector button.
Selecting the type of audio input signal
Audio Sel
A
DTR-6.4/5.4 Remote controller
Notes on DTS:
• If you play a DTS-formatted CD or LD when the “PCM”
setting is selected on the DTR-6.4/5.4, the DTS encoded signal
will not be decoded and noise will be output. This noise could
damage the amplifier and speakers. Therefore, be sure to select
“Auto” or “DTS” and use the digital input jacks (OPT or
COAX) to connect the DTS source.
• If you play a DTS-formatted CD or LD when “Auto” is
selected, you may hear a noise for a short while until the DTS
decoder recognizes the DTS-encoded signal and starts
operating. This is not a malfunction.
• If you press the pause or skip button on the player while playing
a DTS source, a short noise may be heard. This is not a
malfunction. In such cases, try playing the source in the “DTS”
selected.
• The DTS indicator on the DTR-6.4/5.4 lights while a DTS
source is played. When playback finishes and the DTS signal
transmission stops, the DTR-6.4/5.4 remains in DTS mode and
the DTS indicator remains lit. This prevents noise when you
operate the pause or skip button on the player. Therefore, if the
source is immediately switched from DTS to PCM, the PCM
signal may not be played. In this case, stop the playback of the
source on the player for about three seconds and then resume
playback.
• You may not be able to play some DTS source signals from
certain CD players and LD players even when you connect the
player to the DTR-6.4/5.4 digitally. This is because the digital
signal has been processed (such as the output level, sampling
frequency, or frequency response) and the DTR-6.4/5.4 cannot
recognize the signal as DTS data. Therefore you may hear noise
when you play a DTS source while processing the signal.
• The outputs for the VIDEO 1 OUT, VIDEO 2 OUT, and TAPE
OUT output analog audio signals. Do not record from CDs or
LDs that support DTS using these outputs. If you do, the DTS-
encoded signal will be recorded as noise.
• If a CD or LD encoded in the DTS format is played back with
“PCM” selected, only noise will be produced. Always select
“Auto” or “DTS” when playing back DTS-encoded sources.