Filter
Top Products
49
Enjoying music in the remote zone
--
/
---
123
456
+
10 0
789
Audio Sel
Muting
Angle
Subtitle
TV
/
VCR
Random
Audio Adjust
Enter
Search
Input Selector
Dimmer
Display
StereoDirect
All ST
VOL
C
H
Disc
Pure A
Rec
DSP DSP Re
-
EQ
Level
Zone 2
SURR
THX
AM
V
1
DVD
V
3
V
4
V
5
C
D
V
2
P
H
TAP TUN
RC
-
534M
Zone 2
On/Standby
Level
/
Level
/
Zone 2
Zone 2 indicator
Input source buttons
Input Selector
buttons
Off
1. Press the Zone 2 button.
2. Select an input source.
After pressing the Zone 2 button, you must press an input
source button within 5 seconds. The Zone 2 indicator lights.
Ex.: When the CD button is pressed.
To select the same source for the remote zone that is selected
for the main zone, press the Zone 2 button again until
“Zone2Sel:SOURCE” appears in the display.
• When “Zone2Sel:Off” is displayed, the output to the remote
zone is turned off.
• When you are not using the remote zone (Zone 2), press the
OFF button to turn off the Zone 2 indicator.
Notes:
• If a sleep time is set with the Sleep button, the output to the
remote zone will also turn off when the sleep time elapses.
• If the source for the main zone is selected as the source for the
remote zone and the source for the main zone is changed, then
the source for the remote zone will change as well.
• The Zone 2 terminal is an analog output. Digital signals are not
output. If no sound is heard from the selected input source,
check if the component is connected to the analog inputs.
• If the Rec Out button is pressed in the main room while
someone is using the system in the remote zone, the Zone 2
function will be deactivated and the source will turn off in the
remote zone.
• If you select FM (or AM) with the Tuner input source button
when the source for the remote zone (Zone 2) is set to AM (or
FM), the output for the remote zone also changes to AM (or
FM).
• When you are using the remote zone (Zone 2), system
operation will not work.
• In the remote zone, you can only play the source in the 2-
channel mode. You cannot play the source in the remote zone in
the surround mode.
Using the buttons
With the DTR-6.4/5.4 in the standby state, turn on the
output to the remote zone (Zone 2):
After pressing the Zone 2 button, press the On button within 5
seconds. The Zone 2 indicator lights.
To turn off output to the remote zone (Zone 2), press the Zone 2
button and then the Standby button within 5 seconds.
Select an input source:
After pressing the Zone 2 button, press an input source button
within 5 seconds.
If tuner is selected with the TUN button, you can use the CH button
to select a preset radio station.
Note:
After you press the Zone 2 button on the remote controller, the
Standby indicator on the DTR-6.4/5.4 flashes for five seconds.
During this time, you will not be able to perform operations in the
main zone using the remote controller.
When the remote zone (Zone 2) speakers are connected to the
ZONE 2 SPEAKERS terminals, or to an amplifier connected to the
ZONE 2 PRE OUT terminals, adjust the volume as shown below.
Press the Level / buttons on the front
panel.
Adjusting the volume (using the remote controller):
After pressing the Zone 2 button, the Standby indicator on the DTR-
6.4/5.4 will flash for 5 seconds. During this time press the Level /
button.
Using the remote controller
Adjusting the volume for the remote zone
Enter
Search
Zone 2
Enter
Search
Zone 2
Input Selector
V
1
DVD
V
3
V
4
V
5
C
D
V
2
P
H
TAP TUN
Enter
Search
Zone 2
Level