Filter
Top Products
41
ENGLISH
6
Set the various surround parameters.
CH SEL
ENTER
(Remote control unit)
7
If the setting ends, press the “ENTER” or
“SURROUND PARAMETER” button.
NOTE:
• There are four Dolby Surround Pro Logic modes (NORMAL, PHANTOM, WIDE and 3 STEREO). The AVR-
2805 sets the mode automatically according to the types of speakers set during the system setup process
(page 18).
Surround parameters q
Pro Logic IIx and Pro Logic II Mode:
Select one of the modes (“Cinema”, “Music”, “Pro Logic” or “Game”).
• Cinema
This mode is for use with stereo television shows and all programs encoded in Dolby Surround.
• Music
This mode is recommended as the standard mode for auto sound music systems (no video), and is optional
for A/V systems.
Panorama Control:
This mode extends the front stereo image to include the surround speakers for an exciting “wraparound”
effect with side wall imaging.
Select “OFF” or “ON”.
Dimension Control:
This control gradually adjust the soundfield either towards the front or towards the rear.
The control can be set in 7 steps from 0 to 6.
Center Width Control:
This control adjust the center image so it may be heard only from the center speaker; only from the
left/right speakers as a phantom image; or from all three front speakers to varying degrees.
The control can be set in 8 steps from 0 to 7.
• Pro Logic
This mode offers the same robust surround processing as original Pro Logic in case the source contents
is not of optimum quality.
• Game
This mode for playing games.The game mode can only be used with 2-channel audio sources.
DTS NEO:6 mode
• Surround playback can be performed for the analog input and PCM digital input 2-channel signals.
1
Select the DTS NEO:6 mode.
DOLBY PLIIx DTS NEO:6
• The mode switches as shown below each
time the button is pressed.
2
Play a program source.
3
Set the surround parameter
mode.
4, 6
1
5
4, 6
7
3, 7
5
The DTS NEO:6
Cinema or Music
mode can be chosen
directly by pressing
the CINEMA or
MUSIC button on the
remote control unit
during playback in the
DTS NEO:6 mode.
1
3, 5 1, 4, 6
4
Select the play mode.
MODE: Music
*Surr Parameter
MODE: Cinema
*Surr Parameter
Display
5
Select the various parameters.
6
Adjust the parameter settings.
SELECT
(Main unit)
SELECT
(Main unit) (Remote control unit)(Main unit)
(Remote control unit)
(Main unit)
SELECT
(Main unit)
(Remote control unit)
(Remote control unit)(Main unit)
SELECT
(Main unit) (Remote control unit)
NOTE:
• When “Default” is selected and the CURSOR
left button is pressed, “MODE” and “TONE”
are automatically reset to the default values and
“CINEMA EQ” is set to “OFF”.
When the surround parameters are set using
the buttons on the main unit, stop operating
buttons after completing the settings. The
settings are automatically finalized and the
normal display reappears after several seconds.
When the settings are made using the buttons
on the remote control unit, press the “ENTER”
or “SURROUND PARAMETER” button to
finish.
Surround parameters w
DTS NEO:6 Mode:
• Cinema
This mode is optimum for playing movies. Decoding is performed with emphasis on separation
performance to achieve the same atmosphere with 2-channel sources as with 6.1-channel sources.
This mode is effective for playing sources recorded in conventional surround formats as well, because the
in-phase component is assigned mainly to the center channel (C) and the reversed phase component to
the surround (SL, SR and SB channels).
• Music
This mode is suited mainly for playing music. The front channel (FL and FR) signals bypass the decoder
and are played directly so there is no loss of sound quality, and the effect of the surround signals output
from the center (C) and surround (SL, SR and SB) channels add a natural sense of expansion to the sound
field.
CENTER IMAGE (0.0 to 1.0: default 0.3):
The center image parameter for adjusting the expansion of the center channel in the DTS NEO:6 MUSIC
mode has been added.
7
When the surround parameters are set using
the buttons on the main unit, stop operating
buttons after completing the settings. The
settings are automatically finalized and the
normal display reappears after several seconds.
When the settings are made using the buttons
on the remote control unit, press the “ENTER”
or “SURROUND PARAMETER” button to
finish.