Filter
Top Products
46
C4630 SE HOME AUDIO SYSTEM
Using the C4630 SE with Sonance Navigator
®
K2 and K1 Programmable Keypads
The C4630 SE is also compatible with Sonance Navigator K1 and K2 keypads. These programmable keypads provide
additional capability for zones that require more sophisticated control than the C4630 SE Main and Numeric keypads offer.
NOTE: For detailed K1 and K2 programming instructions please
refer to the documentation that is available for those keypads.
Wiring K2 and K1 Keypad Connections
Sonance K1 and K2 keypads connect to the C4630 SE the same way as the C4630
SE Main Keypad:
1. In direct runs from keypad to controller, pull a length of CAT5 wire from every
keypad mounting location to the C4630 SE location. The maximum length of any
single CAT5 cable connecting a K1 or K2 to the C4630 SE is 250’.
2. Terminate each CAT5 cable with RJ45 connectors on one end. Follow the TIA 568B
wiring standard (see
Figure 66
).
3. Connect the CAT5/RJ45 cable to the zone’s Keypad Controller Port on the C4630 SE
(see
Figure 67
) and to the multi-pin connector on the back of the keypad. Refer to
the keypad instructions for details about wiring to the keypad.
Powering K2 Keypads
The K2 keypad requires more current than the C4630 SE Main/Numeric Keypad
combination does. You need to take special care when using these keypads to
ensure there is adequate current to properly run all connected keypads.
C4630 SE supplies 1A of total keypad current through its keypad connections. When the
rear-panel Z
ONE 4 – 6 KEYPAD POWER switch (see
Figure 68
) is in the INT (internal)
position this current is evenly divided between all six Zone Keypad Connections. When the
switch is in the EXT (external) position, the C4630 SE supplies all 1A of current to Zones
1 – 3, while Zones 4 – 6 must be powered by an external PS2 power supply (available
separately) connected to the Z
ONE 4 – 6 KEYPAD EXTERNAL POWER Connection (see
Figure 68
).
The table below shows how many of each type of keypad can be used:
RJ45 Connector
(Flat Side UP)
TIA 568B
Wiring Standard
PIN
1
2
3
4
5
6
7
8
COLOR
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
SIGNAL
No Signal
No Signal
No Signal
IR Data
Status
No Signal
Ground
+12V DC
Figure 66:
Keypad Connection RJ45 Pinout
Z
O
N
E
1
Z
O
N
E
2
Figure 67:
C4630 SE Keypad Controller Ports
F1AL 12VDC
RS-232
12 VDC
1.0 A IN
ZONE 4-6
KEYPAD POWER
INT
EXT
–
+
F
1AL 12VD
C
12 VDC
1.
0
A I
N
Z
ONE 4-
6
K
EYPAD P
O
WER
INT
EXT
–
+
Figure 68:
Keypad External Power
Connection
Z
ONE
4 – 6 K
EYPAD
I
NTERNAL
P
OWER
Switch Position
INT (Internal)
Supplies 1A Total
Up to
6 Sets
Up to
12 Sets
Up to
12
Up to
24
Up to
6
Up to
12
Up to
3
Up to
7
EXT (External, w/PS2
Power Supply)
Supplies 2A Total
C4630 SE
Main/Numeric Keypads
Max LED Brightness,
(Each Set Draws 165mA)
K1 Keypads
Backlight ON,
(Each Draws
70mA)
K2 Keypads
Med LED
Brightness,
(Each Draws
150mA)
K2 Keypads
Max LED
Brightness,
(Each Draws
265mA)