Filter
Top Products
The system and the other setup
12
113
en
1 Select ‘
Multi Ch In Setup
’ from the
Other Setup
menu.
2 Select the ‘
SW Input Gain
’ setting you want.
• 0dB – Outputs sound of the subwoofer at the level
originally recorded on the source.
• +10dB – Outputs sound of the subwoofer at the level
increased by 10 dB.
3 Select the ‘
Video Input
’ setting you want.
When the multi-channel input is selected as an input
function, you can display the video images of other input
functions. The video input can be selected from the
following: DVD, TV/SAT, DVR, VIDEO 1, VIDEO 2, OFF.
4 When you’re finished, press
RETURN
.
You will return to the Other Setup menu.
ZONE Audio Setup
If you’ve made MULTI-ZONE connections (see Using the
MULTI-ZONE controls on page 85), you may need to
specify your volume setting.
1 Select ‘
ZONE Audio Setup
’ from the
Other Setup
menu.
2 Select the volume level setting of
ZONE 2
1
and
ZONE 3
.
• Variable – Use this setting if you’ve connected a
power amplifier in the sub room (this receiver is
simply being used as a pre-amp) and you will be
using this receiver’s controls to adjust the volume.
• Fixed – Use this setting if you’ve connected a fully
integrated amplifier (such as another Pioneer VSX
receiver) in the sub room and want to use that
receiver’s volume controls.
With the Fixed setting, the source is sent from this
receiver at maximum volume, so make sure the volume is
quite low in the sub zone at first, and then experiment to
find the correct level.
3 When you’re finished, press
RETURN
.
You will return to the Other Setup menu.
Power ON Level Setup
The volume can be set so that it is always set to the same
level when the receiver’s power is turned on.
1Select ‘
Power ON Level Setup
’ from the
Other
Setup
menu.
2 Select the
Power ON Level
setting you want.
• LAST – When the power is turned on, the volume is
set to the same level as when the power was last
turned off.
•“---” – When the power is turned on, the volume is set
to minimum level.
• –80.0dB to +12.0dB – Specify the volume to be set
when the power is turned, in steps of 0.5 dB.
It is not possible to set a volume level greater than the
value specified at Volume Limit Setup.
3 When you’re finished, press
RETURN
.
You will return to the Other Setup menu.
Volume Limit Setup
Use this function to limit the maximum volume. The
volume cannot be increased above the level set here,
even by operating MASTER VOLUME button (or the dial
on the front panel).
4d.Other Setup
A/V RECEIVER
Exit Return
3. ZONE Audio Setup
4. Power ON Level Setup
5. Volume Limit Setup
6.
Remote Control Mode Setup
7.
Flicker Reduction Setup
2. Multi Ch In Setup
1. KURO LINK Setup
4d2.Multi Ch In Setup
A/V RECEIVER
Exit Finish
SW Input Gain : 0dB
Video Input : DVD
4d2.Multi Ch In Setup
A/V RECEIVER
Exit Finish
SW Input Gain : +10dB
Video Input : DVD
2. Multi Ch In Setup
3. ZONE Audio Setup
4. Power ON Level Setup
5. Volume Limit Setup
6.
Remote Control Mode Setup
7.
Flicker Reduction Setup
1. KURO LINK Setup
4d.Other Setup
A/V RECEIVER
Exit Return
4d3.ZONE Audio Setup
A/V RECEIVER
Exit Finish
ZONE 2 Volume Level : Variable
ZONE 3 Volume Level : Variable
Note
1 If you selected ZONE 2 in the Surround back speaker setting on page 109, you won’t be able to change the volume level.
4d.Other Setup
A/V RECEIVER
Exit Return
3. ZONE Audio Setup
4. Power ON Level Setup
5. Volume Limit Setup
6.
Remote Control Mode Setup
7.
Flicker Reduction Setup
2. Multi Ch In Setup
1. KURO LINK Setup
4d4.Power ON Level Setup
A/V RECEIVER
Exit Finish
Power ON Level : LAST
SC-9540.book 113 ページ ２００９年４月２４日 金曜日 午後１時４２分