Pioneer sc-9540 Stereo Receiver User Manual


 
Using other functions
09
84
en
4 Press
RETURN
to confirm and exit the menu.
Switching the speaker system
If you selected Speaker B in Surround back speaker
setting on page 109, three speaker system settings are
possible using SPEAKERS. If you selected Normal, Front
Bi-Amp or ZONE 2, the button will simply switch your
main speaker system on or off. The options below are for
the Speaker B setting only.
1
•Use
SPEAKERS
on the front panel to select a
speaker system setting.
As mentioned above, if you have selected Normal, the
button will simply switch your main speaker system (A)
on or off.
Press repeatedly to choose a speaker system option:
SPA – Sound is output fr om speaker system A and
the same signal is output from the pre-out terminals.
SPB – Sound is output from the two speakers
connected to speaker system B. Multichannel
sources will not be heard. The same signal is output
from the surround back channel pre-out terminals.
Setting What it does Option(s)
V.CONV
(Digital Video
Conversion)
Converts video signals for output
from the MONITOR OUT jacks
(including HDMI OUT connector)
for all video types (see page 25).
ON
OFF
RES
a
(Resolution)
Specifies the output resolution of
the video signal (when analog
video input signals are output at
the HDMI OUT connector, select
this according to the resolution of
your monitor and the images you
wish to watch).
AUTO
PURE
480p/576p
720p
1080i
1080p
ASP
b
(Aspect)
Specifies the aspect ratio when
analog video input signals are
output at the HDMI output. Make
your desired settings while
checking each setting on your
display (if the image doesn’t match
your monitor type, cropping or
black bands appear).
THROUGH
NORMAL
PCINEMA
c,d
(PureCinema)
This setting optimizes the picture
for film material when the video
output is set to progressive.
Usually set to AUTO; but try
switching to OFF if the picture
appears unnatural.
Additionally, certain PAL movie
video (576i, 25 frames/second STB
video output or DVD disc playback,
etc.) that contain film progressive
material cannot be recognized as
such by this receiver.
AUTO
PAL
OFF
P.MOTION
c,d
(Progressive
Motion)
Adjusts the motion and still picture
quality when video output is set to
progressive.
–4 to +4
Default: 0
YNR
c
Adjusts the amount of noise
reduction (NR) applied to the Y
(brightness) component.
0 to +8
Default: 0
DETAIL
c
Adjusts how sharp edges appear.–4 to +4
Default: 0
SHARP
c,e
(Sharpness)
Adjusts the sharpness of the high-
frequency (detailed) elements in
the picture.
–4 to +4
Default: 0
BRIGHT
c
(Brightness)
Adjusts the overall brightness. –6 to +6
Default: 0
CONTRAST
c
Adjusts the contrast between light
and dark.
–6 to +6
Default: 0
HUE
c,f
Adjusts the red/green balance. –6 to +6
Default: 0
CHROMA
c
(Chroma
Level)
Adjusts saturation from dull to
bright.
–6 to +6
Default: 0
a.• When set to a resolution with which the TV (monitor) is not
compatible, no picture is output. Also, in some cases no picture will
be output due to copyright protection signals. In this case, change
the setting.
• When AUTO is selected, the resolution is selected automatically
according to the capacity of the TV (monitor) connected by HDMI.
When PURE is selected, the signals are output with the same
resolution as when input (At this time, video signals are only output
from the same type of terminals to which they were input).
• When a display is connected by HDMI, if this is set to something
other than PURE and 480i/576i analog signals are input, 480p/576p
signals are output from the component output terminals.
• Conversion to 1080p is only performed for 480
i, 57
6i, 480p and
576p input signals.
b.• If the image doesn’t match your monitor type, adjust the aspect
ratio on the source component or on the monitor.
• This cannot be set when the resolution is set to PURE.
NORMAL setting is only displayed when 480i/p or 576i/p video
signals are being input.
c.This setting is only displayed when 480i or 576i video signals are
being input.
d.This setting is only valid for component outputs.
e.This setting is not valid for HDMI outputs.
f. This setting is not displayed for component inputs.
Note
1 • The subwoofer output depends on the settings you made in Manual speaker setup on page 108. However, if SPB is selected above, no sound
is heard from the subwoofer (the LFE channel is not downmixed).
• Depending on the settings in Surround back speaker setting on page 109 output from the surround back pre-out terminals may change.
• All speaker systems (except Speaker B connections) are switched off when headphones are connected.
Setting What it does Option(s)
PHONES
SPEAKERS
CONTROL
MULTI-ZONE
ON/OFF
MCACC
SETUP MIC
PARAMETER
ENTER
(TUNE)
(TUNE)
(PRESET)(PRESET)
AUDIO VIDEO
TUNER EDIT
USBHDMI 4
VIDEO CAMERA
iPod
iPhone
AUTO SURR/ALC/
STREAM DIRECT
HOME
THX
STANDARD
SURROUND
ADVANCED
SURROUND
STEREOBAND
HOME MENU RETU RN
SC-9540.book 84 ページ 2009年4月24日 金曜日 午後1時42分