Filter
Top Products
Controlling the rest of your system
10
90
en
Programming signals from other
remote controls
If the preset code for your component is not available, or
the available preset codes do not operate correctly, you
can program signals from the remote control of another
component. This can also be used to program additional
operations (buttons not covered in the presets) after
assigning a preset code.
1
1 Press and hold
REMOTE SETUP
, then release it after
the LED flashes twice.
2 Use the number buttons to enter 9, 7, 5.
The LED flashes twice.
3 Press the input function button for the component
you want to control.
2
4 Point the two remote controls towards each other,
then press the button that will be doing the learning on
this receiver’s remote control.
The LED flashes continuously for about 5 seconds.
3
•The remote controls should be 3 cm (1 inch) apart.
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal to
this receiver’s remote control.
For example, if you want to learn the playback control
signal, press and hold briefly. If the LED flashes twice
then turns off, this indicates that learning has been
successful. If the LED only flashes once, learning has
failed.
4
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons
available are shown below:
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
Erasing the remote control button
settings
This erases the buttons you have programmed and
restores the button to the factory default.
1 Press and hold
REMOTE SETUP
, then release it after
the LED flashes twice.
2 Use the number buttons to enter 9, 7, 6.
The LED flashes twice.
3 Press the input function button corresponding to
the command to be erased, then press the button to be
erased twice.
To erase all the settings stored at the input function
buttons, press the input function button twice here.
The LED flashes twice to confirm the button has been
erased.
4 Repeat step 3 to erase other buttons.
Note
1 The remote can store about 200 preset codes (this has been tested with codes of Pioneer format only).
2 • You can’t assign TUNER, HOME MEDIA GALLERY, iPod USB, XM or SIRIUS.
• The TV CONTROL buttons (TV, TV VOL +/–, TV CH +/– and INPUT) can only be learned after the TV CTRL is pressed.
3 The learning mode is cancelled if no remote control signal is received within 5 seconds.
4 • Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
• Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or
farther apart.
•
If
the LED flashes once, it means the memory is full. See Erasing the remote control button settings above to erase a programmed button
you’re not using to free up more memory (note that some signals may take more memory than others).
DVD BD DVR HDMI
TV CD CD-R
TUNER XM SIRIUS
HOME MEDIA
GALLERY
iPod USB
INPUT
123
HDMI OUT
SLEEPMCACC
INPUT
SELECT
SIGNAL SEL
456
DIMMERA.ATTSBch
789
CLASS
MASTER
VOLUME
CH LEVELD.ACCESS
/CLR
0
ENTER
RECEIVER
SOURCE
3 cm (1 inch)
DVD BD DVR HDMI
TV CD CD-R
TUNER XM SIRIUS
HOME MEDIA
GALLERY
iPod USB
MUTE
AUDIO
123
HDMI OUT
SLEEPMCACC
INPUT
SELECT
SIGNAL SEL
456
DIMMERA.ATTSBch
789
CLASS
MASTER
VOLUME
CH LEVELD.ACCESS
/CLR
0
ENTER
RECEIVER
SOURCE
VIDEO
SOURCE
123
456
789
/CLR
0
ENTER
INPUT
VOLCH
TV CONTROL
T.EDIT
GUIDE
TOP MENU
BAND
RETURN
iPod CTRL
HOME
MENU
LIST
TOOLS
CATEGORY
AUDIO
PARAMETER
AUTO/ALC/
DIRECT
PHASE CTRL STATUS
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
HDD
PGM
DVD
STANDARDSTEREO
MENU
ADV SURR
ENTER
ANT
THX
MULTI OPE
MPX PQLS
MEMORY
TUNE
PRESET PRESET
TUNE
VIDEO
PARAMETER
RECEIVER
TV CTRL
GUIDE
TOP MENU
LIST
TOOLS
ENTER
RETURN
HOME
MENU
HDD DVD
STATUS
AUDIO
INFO
DISP
CH
MENU
SC-9540.book 90 ページ ２００９年４月２４日 金曜日 午後１時４２分