Marantz SR9600 Home Theater System User Manual


 
ENGLISH
64
HDMI
i.LINK (AUDIO)
CAUSE
The connected monitor or
projector does not support HDCP.
The HDMI input of on the TV is
not on.
The HDMI output on the source
component (DVD, Set Top Box,
etc.) is not on.
The HDMI mode is not correctly
set on the SR9600.
The HDMI output video resolution
of the source component (DVD,
Set Top Box, etc.) does not
match the TV specifications.
The device is connected with a
non-standard HDMI cable.
Power to the SR9600 is off.
(When the SR9600 is on
standby, HDMI connections
cannot be turned on.)
The connection between HDMI
components was not
authenticated.
The SR9600 SETUP menu
does not support HDMI output.
The connection is being
authenticated between the
HDMI devices.
The HDMI audio output of the
source component (DVD, Set
Top Box, etc.) is not on.
The signal format of the source
component (DVD, Set Top Box,
etc.) is not supported by the
SR9600.
The SR9600 is set to the HDMI
audio THROUGH mode.
The DVD player does not
support CPPM, therefore it
cannot output HDMI audio.
SYMPTOM
The display does not
appear over an HDMI
connection.
The SR9600 SETUP
menu does not appear
over an HDMI connection.
Time is needed for the
display of an HDMI
connection to appear.
Audio is not played back
over an HDMI
connection.
DVD-Audio is not played
back over an HDMI
connection.
REMEDY
Set HDMI input so that it turns on, as
explained in the TV's instruction manual.
Set HDMI output so that it turns on, as
explained in the source component's
instruction manual.
Set HDMI input on the FUNC INPUT
SETUP menu as explained on page 33.
Set the resolution so that it matches, as
explained in the instruction manuals of
both components.
A 5 m or shorter cable is recommended
to ensure stable operation and prevent
image quality deterioration.
Turn on the power to the SR9600.
Shut off and then turn the power back on
to the SR9600, TV and source
component.
Use the COMPONENT VIDEO, S-VIDEO
or VIDEO output.
There is nothing wrong with the system.
Some HDMI devices require time for
authentication.
Set the HDMI audio output so that it turns
on, as explained in the source
component's instruction manual.
Set the HDMI audio output so that it can
connect to the SR9600, as explained in
the source component's instruction
manual.
In the THROUGH mode, sound is not
produced from the SR9600. Set it to
ENABLE. (see page 44)
Use a DVD-Audio player that supports
CPPM.
Turn on PCM downsampling on the
DVD player.
Use an analog connection.
CAUSE
The connected component
does not support i.LINK
(Audio).
The connected component
does not support DTCP (Digital
Transmission Content
Protection).
The i.LINK mode on the
SR9600 is not correctly set.
The
i.LINK
output of the source
component (DVD, etc.) is not on.
Power to one of the
components in a daisy chain or
tree connection is not on.
There are too many i.LINK
devices outputting signals on the
i.LINK bus.
Authentication is being
performed for copyright
protection.
Components disable analog
output when an i.LINK
connection is on.
Components disable digital
output when an i.LINK
connection is on.
REMEDY
Use a component that supports i.LINK
(Audio).
Use a device that supports DTCP.
Set i.LINK input on the SETUP menu as
explained on page 34.
Set i.LINK output so that it turns on, as
explained in the source component
instruction manual.
Turn on power to all devices in the i.LINK
connection.
Disconnect unused i.LINK devices.
There is nothing wrong with the system.
Some components require time for
authentication.
Change the i.LINK setting on the
component.
Change the i.LINK setting on the
component.
SYMPTOM
Audio is not played back
over an i.LINK
connection.
Audio is not played back
for a few seconds when
the input source is
changed or the power is
shut off and turned back
on.
The analog audio of the
connected component is
not played back over
i.LINK.
The digital output of the
connected component is
not played back over
i.LINK.
CAUSE
The current HDMI connection
does not support Super Audio
CDs.
SYMPTOM
Super Audio CD is not
played back over an
HDMI connection.
REMEDY
Use an analog connection.
05.4.27, 5:49 PMPage 64