Filter
Top Products
37
ENGLISH
Notes:
• The measured speaker distance may differ from
the actual distance from speakers. Nevertheless,
the measured value is suitable for the speakers.
• The included microphone is designed specifically
for the SR9600. Other microphones do not
guarantee suitable measurement results. Use the
included microphone to conduct measurements.
• During measurement, press the OK/ENTER or
EXIT button to cancel measurement.
• In some rooms, an error may occur during auto
speaker setup or it may not be possible to set
speaker distance correctly because of room
acoustics. In such case, set the speaker distance
using “MANUAL SETUP”.
• If the SPEAKER C selector switch (rear panel) is
set to “ON”, the surround back speakers do not
output audio.
Error indications during measurement
If trouble occurs during measurement, an error
message is displayed on the monitor screen and
FL display. Those errors and their remedies are
described below.
8.
Once finished, disconnect the microphone
from the SR9600.
9.
When “CHECK RESULT” appears on the FL
display, press the OK/
ENTER
button.
The MRAC 1 Size menu displays measurement
results indicating which speakers are connected
and their sizes.
10.
Move the cursor to “NEXT” with the or
cursor buttons and press the OK/ENTER
button.
The distance from the microphone to each of
the speaker is displayed.
11.
Select either m (meters) or ft (feet) for UNIT
with the or cursor buttons.
12.
Move the cursor to “NEXT” with the or cursor
buttons and then press the OK/ENTER button.
The frequency is automatically compensated for
to the flat level of the all channel and is indicated
in dB by channel. (EQ mode: AUTO 1)
This compensation level is indicated
somewhere between -12 dB and +12 dB in 0.5
dB increments.
13.
Select “CH” with the or cursor buttons.
14
.
Move the cursor to “NEXT” with the , , ,and
cursor buttons and press the OK/ENTER
button.
The frequency is automatically approximated
based on the front speaker characteristics and
is indicated in dB by channel. (EQ mode:
AUTO 2)
This compensation level is indicated somewhere
between -12 dB and +12 dB in 0.5 dB
increments.
15.
Select “CH” with the or cursor buttons.
16.
Move the cursor to “NEXT” with the or
cursor buttons and press the OK/ENTER
button.
The speaker output level is automatically
balanced and indicated in dB by channel.
17.
Move the cursor to “EXIT” with the , , and
cursor buttons and press the OK/ENTER
button to end calibration.
Notes:
• For settings, see the individual settings in “2-2
MANUAL SETUP”.
• To make changes to individual speakers, select “2.
SPEAKER SETUP” from the MAIN MENU,
then select MANUAL from the 2-1 SPEAKER
SETUP.
• If using a THX certified speaker system, select
“SPEAKER SIZE” from the MANUAL SETUP
menu. Then, turn “THX SPKR” on. Move the
cursor to “LPF/HPF” with the
, , and
cursor buttons and select “80Hz” with the or
cursor buttons.
MIC SETUP ERROR
The microphone (MC-10) is not properly
connected.
→ Check the microphone connection.
TOO MUCH NOISE
Measurement cannot be done correctly
because of excessive ambient noise.
→ Either temporarily turn off power to noisy
devices such as air conditioning or move
them out of the room.
→ Retry measurement when the room is
quiet.
2-2 MANUAL SETUP
1.
Select “2. SPKR SETUP” from the MAIN
MENU.
2.
Select “MANUAL SETUP” with the or
cursor buttons.
3.
Press the OK / ENTER button to enter the
selection.
<SPEAKER SIZE>
When setting the speaker size in the SPEAKER
SIZE menu, use the guidelines below.
LARGE:
The complete frequency range for the channel
you are setting will be output from the speaker.
SMALL:
Frequencies of the channel you are setting that
are lower than approx. 80 Hz will be output from
the subwoofer.
If the SUB. W is set to “NONE” and the front
speakers are set to “LARGE,” then the sound will
be output from both the left and right speakers.
4.
Select each speaker with the or cursor
buttons.
5.
Set the size of each speaker with the or
cursor buttons.
6.
After you complete this portion of the setup,
move the cursor to “NEXT” with the , ,
and cursor buttons and press the OK/
ENTER button to go to the next page.
AUTO SETUP 3
FINISH !!
CHECK RESULT
SPEAKERS
SIZE : OK
DISTANCE : OK
FLAT
M
ODE : OK
FRONT
M
ODE : OK
RETURN EX IT
M
RAC 1 S I ZE
FRONT L : LARGE
CENTER : S
M
ALL
FRONT R : LARGE
SURR.R : LARGE
SURR.B R : S
M
ALL
SURR.B L : S
M
ALL
SURR. L : LARGE
SUB
W
: YES
LPF HPF : 80Hz
RETURN NEXT EX IT
M
RAC 2 D ISTANCE
UNIT : ft
FRONT L : 30.00f t
CENTER : 1 9. 33 f t
FRONT R : 29.66f t
SURR.R : 2 1 . 50f t
SURR.B R : 12.33ft
SURR.B L : 11.66ft
SURR. L : 1 6 . 33f t
SUB
W
:12.50ft
RETURN BACK NEXT EX IT
M
RAC 3 FREQ. AUTO1
M
ODE FLAT 63 -6.0
CH :SBL 100 -1.5
250 +1.5
315+12.0
630 +8.5
2k +1.5
4k -9.0
8k-10.5
12. 5k-12.0
RETURN BACK NEXT EXIT
63
+12
-12
0
16kHz
M
RAC 3 FREQ. AUTO2
M
ODE FRONT 63 -6.0
CH :SR 100 -1.5
250 +1.5
315+12.0
630 +8.5
2k +1.5
4k -9.0
8k-10.5
12. 5k-12.0
RETURN BACK NEXT EX IT
63
+12
-12
0 B
16 Hz
M
RAC 4 LEVEL
M
ODE FLAT
FRONT L : 0.0dB
CENTER : - 6 . 5dB
FRONT R : - 1.5dB
SURR.R : +1.0dB
SURR.B R : +9. 5dB
SURR.B L : +12. 0dB
SURR.L : - 2.5dB
SUB
W
:-12.0dB
RETURN BACK EXIT
SPEAKER SIZE
THX SPKR : NO
SUB
W
: YES
FRONT : LARGE
CENTER : LARGE
SURR. : LARGE
SURR.B : 2CH
SURR.B SIZE : LARGE
LPF /HPF : 80Hz
BASS
M
IX : BOTH
RETURN NEXT EX IT
05.4.27, 5:41 PMPage 37