Filter
Top Products
ENGLISH
56
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through the SR9600 is sent to
the record outputs.
This means that any program you are watching or
listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD-R/MD OUT, VCR1 OUT, and VCR2/DVD-R
OUT in the Record mode.
To record the input source signal you are
currently watching or listening to
1.
Select the input source to record by turning
the INPUT SELECTOR knob on the front
panel or simply select a source from among
the Source Select screen on page 1/8 on the
remote control unit.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal is
output to TAPE OUT, CD-R/MD OUT, VCR1
OUT, and VCR2/DVD-R OUT for recording.
3.
Start recording to the recording component as
desired.
MULTI
SPEAKER
F/PBANDTHXTHXPURE DIRECTPURE DIRECT UP
DOWN
TUNING
AUX 1 INPUT
RAUDIO
DIGITAL S-VIDEO
LVIDEO
POWER ON/STANDBYPOWER ON/STANDBY
VOLUME
UPDOWN
INPUT SELECTORINPUT SELECTOR
PHONESPHONES
STANDBYSTANDBY
AV SURROUND RECEIVER SR9600AV SURROUND RECEIVER SR9600
SURROUNDSURROUND
MIC
ENTER
MENU
PURE DIRECTPURE DIRECT THXTHX
7.1CH INPUT
MODEMODE AUTOAUTO
MUMULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
MRAC
AUTO TUNE
1.
VIDEO ON/OFF
When no video signal is connected to the SR9600
or a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
setting the video off mode.
1.
To set the video off mode, tap the A/V Amp
and press the page up button until page 5/8 is
displayed.
Tap the Video off on the remote control unit.
“V-OFF” indicator will be illuminated when this
function is activated.
2.
To cancel the Video Off mode, tap the Video
off on the remote control unit again.
SELECTING ANALOG AUDIO INPUT
OR DIGITAL AUDIO INPUT
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for
each input source.
1.
Tap the A/V Amp and press the page up
button until page 5/8 is displayed. Tap the A/D
on the remote control unit.
When the A/D is tapped, the input mode is
switched in the following sequence:
Auto → i.LINK → HDMI → Digital→ Analog
→ Auto ....
Auto mode:
The types of signals being input to the digital
and analog input jacks for the selected input
source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
i.LINK mode:
i.LINK mode can be selected only when an
i.LINK device has been assigned as an input
source.
HDMI mode:
HDMI mode can be selected only when an HDMI
input has been assigned as an input source.
Digital mode:
The input signal is fixed to an assigned digital
input terminal.
Analog mode:
The analog input jacks are selected.
This selection is temporary and will not be stored in
memory.
To store changes to the input mode, select “1.
INPUT SETUP” from the MAIN MENU. (See page
32)
5/8 A/V Amp
Mode
wed Jun 01 4:40
pm
1.
DISPLAY MODE
You can select the display mode for the front panel
display on the SR9600.
1.
To select this mode, press the DISPLAY
button on the front panel or tap the Display on
the remote control.
When this button is pressed, the Display
mode is switched in the following sequence:
Normal mode → Level Meter mode → Auto
Display Off mode → Display Off mode →
Normal mode → ....
Normal mode:
Displays the selected component.
Level meter mode:
Displays the current output level of up to 7.1
channels as a bar graph.
Auto Display Off mode:
The display is off. But, if you make a change to
the unit such as the input or surround mode, the
display will show that change, then go back to
off after about 3 seconds. When changing the
volume, it is not displayed.
Display Off mode:
The display is off completely.
Note:
• Only the “DISP” indicator will be illuminated on
the front panel display when the Display Off
mode is selected.
• Only SBL is displayed in the Level Meter mode if
"SURR.B" on the SPEAKER SIZE menu in the
SETUP MENU is set to 1 channel (1CH).
DIGITAL
HDMI
L
SL
dB
DVD:AT
>
HDMI.2
CR
SR
S
LFE
DIGITAL EX
+18.0
ATTPEAKSPKR A
.
BMULTI A
.
B
.
SPK
SLEEP V-OFF Re-EQ NIGHT
S
B
L
S
L
S
R
S
B
RLCR
S
W
5/8 A/V Amp
Mode
wed Jun 01 4:40
pm
1.
MULTIMULTI
SPEAKERSPEAKER
F/PF/PBANDBANDTHXTHXPURE DIRECTPURE DIRECT UPUP
DOWNDOWN
TUNINGTUNING
AUX 1 INPUT
RAUDIO
DIGITAL S-VIDEO
LVIDEO
POWER ON/STANDBY
VOLUME
UPDOWN
INPUT SELECTOR
PHONES
STANDBY
VER SR9600AV SURROUND RECEIVER SR9600
SURROUNDSURROUND
MICMIC
ENTERENTER
MENUMENU
PURE DIRECTPURE DIRECT THXTHX
7.1CH INPUT7.1CH INPUT
MODEMODE AUTOAUTO
MULTIMULTI
A/BA/B
T-MODET-MODE
MEMORYMEMORY CLEARCLEAR
DISPLAYDISPLAY
EXITEXIT
SPEAKERSSPEAKERS
MRACMRAC
AUTO TUNEAUTO TUNE
1.
5/8 A/V Amp
Mode
wed Jun 01 4:40
pm
1.
1/8 A/V Amp
Source Select
wed Jun 01 4:40
pm
1.
05.4.27, 5:48 PMPage 56