Filter
Top Products
20
ENGLISH
RC3200B SETUP
If you want to personalize your RC3200B even
more beyond its standard programming features,
RC3200Setup is the tool to use.
You can find more information and updates to the
software at “http://www.marantz.com”.
RC3200Setup is a visual editor for creating and
configuring RC3200B Configuration Files (NCF)
on your computer. An NCF is a file that is used to
define the RC3200B behavior and appearance of
the LCD touch screen.
Note:
•
It is advised to make backup copies of your own
configurations. This can be done with RC3200Setup.
With RC3200Setup you can:
• generate a Home screen;
• design the page layout and the appearance of
buttons;
• configure the behavior of the hard and soft buttons;
• access RC3200Setup's extended help system
by pressing F1.
• save, duplicate and share NCFs, devices,
buttons, bitmaps or codes with another
RC3200B;
• preview the NCF on the RC3200B emulator;
• download new configurations to your RC3200B
using the included serial cable.
1.
Plug one end of the serial cable in the serial
port on your computer.
2.
Plug the other end of the serial cable into the
serial port on the RC3200B.
Note:
• When the RC3200B is connected to a PC, the
battery lifetime may be reduced.
MINIMUM SYSTEM REQUIREMENTS
• PC with a Pentium 166 MHz or higher processor
• Windows 95/98/ME/XP or NT 4.0/2000
• 32 MB of RAM
• 16 MB of free hard disk space
• Free serial port
Notes:
• Microsoft and Windows are trademarks of the
Microsoft Corporation of the U.S.A. and are
registered in the U.S. and other countries.
• Pentium is a trademark of Intel Corporation in the
U.S. and other countries.
IMPORTANT NOTICES
Take care not to scratch the LCD touch screen
Use your finger to tap the LCD touch screen or use
plastic-tipped pens intended for use with touch
screens.
Never use an actual pen, pencil or other sharp
object on the LCD touch screen.
Protect the RC3200B from extreme temperatures
Keep the RC3200B away from heaters and other
heat sources.
The RC3200B is not waterproof
The RC3200B should not be exposed to rain or
moisture.
Do not store or use the RC3200B in any location
that is extremely damp or wet.
If you spill water on the RC3200B, take out the
batteries and let the RC3200B dry for 48 hours
before reinserting the batteries.
If you spill other liquids like coffee on the
RC3200B, clean it with distilled water. Make sure
no water gets into the housing.
The touch screen of RC3200B contains a glass
element
Do not drop the RC3200B or subject it to any strong
impact.
Replace batteries
The RC3200B has a backup function to prevent
some memory data such as learned RC codes,
macros from being erased when the batteries are
replaced.
However, the setup page memory (LCD, lighting,
date, etc.) will be cleared.
Please reset these contents, after inserting new
batteries.
CLEANING RC3200B
Use a soft, damp cloth to clean RC3200B.
If the LCD touch screen of RC3200B is spoiled,
clean it with a soft cloth moistened with a diluted
window-cleaning solution.
Do not use a corrosive detergent or an abrasive
sponge.
Avoid the use of abundant water.
HOW TO RESET THE RC3200B
Under normal circumstances, you will never have
to reset the RC3200B.
However, on rare occasions, if the RC3200B's
touch screen freezes or if you notice unusual
behavior, you need to perform a reset to get the
RC3200B running again. All customized
commands and devices are retained.
1.
Slide the battery cover off the back of the
RC3200B.
You will see the Reset button in the battery
compartment.
2.
Use an unfolded paperclip to carefully press
the Reset button.
The RC3200B restarts and the Introduction
screen appears. The RC3200B beeps twice to
indicate it is ready for use.
Reset button
05.4.27, 5:37 PMPage 20