Marantz SR9600 Home Theater System User Manual


 
10
ENGLISH
CAUTIONS ON BATTERIES
Use “AA” (R6P) batteries in this remote control
unit.
If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less then a year has passed.
The included battery is only for verifying
operation. Replace it with a new battery as soon
as possible.
When inserting the batteries, be careful to do so
in the proper direction, following the marks in the
remote control unit’s battery compartment.
- To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
Remove the batteries when not planning to use
the remote control unit for a long period of time.
If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules that
apply in your country or area.
REMOTE-CONTROLLABLE RANGE
The distance between the transmitter/receiver of
the remote control unit and the infrared sensor of
the SR9600 should be less than about 16.4 ft (5
meters).
If the transmitter/receiver is pointed away from the
infrared sensor or if there is an obstacle between
them, remote control may not be possible.
REMOTE CONTROLLER
RC3200B
NAMES AND FUNCTIONS
A
Select buttons for navigation bar
These buttons control the navigation bar in LCD
touch screen. Each function may also be provided
with an alphanumeric indicator visible in the
navigation bar of LCD touch screen.
B
CH (Channel) up and down buttons
Press these buttons to select the SR9600 tuner
presets or TV channels.
C
S (Status) button
Press this button to see the SR9600 status on the
LCD touch screen.
D
M (Menu) button
Press this button to enter the OSD menu system.
E
Ex (Exit) button
Press this button to exit the OSD menu system.
F H
(Mute) button
Press this button to mute the sound temporarily.
G
VOL (Volume) up and down buttons
Press these buttons to raise and lower the SR9600’s
volume level.
H
OK and cursor (Up/Down/Left/Right )
buttons
Press these buttons to navigate through the OSD
menu system.
(Refer to “ON SCREEN DISPLAY MENU SYSTEM
on page 30)
I
Page up/down buttons
Press these buttons to scroll up or down the contents
of LCD touch screen.
J
Backlight
ˆ
button
Press this button to turn on the backlight of the
LCD touch screen.
K
Serial port
Connect the RC3200B with your computer using
an RS232C cable for future upgrades.
L
LCD touch screen
The LCD touch screen is divided into different
sections:
LOADING BATTERIES
When you use RC3200B for the first time, you
have to install the batteries.
The RC3200B requires 3 AA batteries (3 x 1.5 V) to
function.
Note:
The included batteries are for verifying functionality
of the remote control unit. When replacing the
batteries, either rechargeable or non-rechargeable
batteries may be used.
1.
Remove the back cover.
2.
Insert the new batteries (AA type) with correct
and polarity.
3.
Close until it clicks.
1/8 A/V Amp
Source Select
wed Jun 01 4:40pm
In this area, you can
see the device you are
operating.
Operate your device
with these soft buttons.
Ex
M
S
VOL
CH
OK
11
12
10
9
8
7
6
5
1
2
3
4
Notes:
Do not mix alkaline and manganese batteries.
Do not mix old and new batteries.
60°
Remote control unit
(RC3200B)
Approx.
16.4 ft (5 m)
05.4.27, 5:36 PMPage 10