Denon AV SURROUND PRE-AMPLIFIER Stereo Amplifier User Manual


 

Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting Specifications
• Connect the cables to be used (vpage 9 “Video Conversion
Function”).
• With HDMI connections, the video and audio signals can be
transferred with a single cable.
• To output the audio signals to the monitor with HDMI connections,
set GUI menu “Manual Setup” – “HDMI Setup” – “Audio” to “TV”
(vpage 32).
Connecting the Monitor
47*%&0
*/
7*%&0
$0.10/&/57*%&0
: 1# 13
7*%&0
*/
)%.*
*/ */
Monitor
Connecting the Playback Components
NOTE
• The component video connectors may be indicated differently on
your monitor. For details, see the monitor’s operating instructions.
• The audio signals output from the HDMI connectors are only the
HDMI input signals.
47*%&0
065
"6%*07*%&0
$0.10/&/57*%&0
: 1# 13
7*%&0
065 065
"6%*0
$0"9*"-
065
3-
065065
)%.*
R
L
R
L
Carefully check the left (L) and right (R) channels and the inputs and
outputs, and be sure to interconnect correctly.
DVD Player
• Connect the cables to be used.
• With HDMI connections, the video and audio signals can be transferred
with a single cable.
DVD player
• Connect an HDP (High-Definition Player) in the same way.
• When using an optical cable or a BNC cable for the digital audio
connection, make the settings at GUI menu “Source Select” – “DVD”
– “Assign” – “Digital” (vpage 48).
• When using a BNC cable for the component video connection, make
the settings at GUI menu “Source Select” – “DVD” – “Assign” –
“Component” (vpage 48).
• When the AVP-A1HDCI and DVD player are connected using an
HDMI cable, also connect the AVP-A1HDCI and monitor using an
HDMI cable.
• If the connected monitor or DVD player only has a DVI-D
connector, use an HDMI/DVI converter cable. When using a DVI
cable, no audio signals are transmitted.
• Use a Deep Color compatible cable for connection to Deep Color
compatible devices.
NOTE
• Use a CPPM-compatible DVD player to play DVD-Audio discs that
are copyright-protected by CPPM.
• The audio signals output from the HDMI connector (sampling
frequency, bit rate, etc.) may be restricted by the connected
device.
• Video signals are not output properly when using devices that are
not HDCP-compatible.
• Video signals are not output if the input video signals do not match
the monitor’s resolution. In this case, switch the DVD player’s
resolution to a resolution with which the monitor is compatible.
• If the GUI menu “Manual Setup” – “HDMI Setup” – “Audio”
setting (vpage 32) is set to “Amp”, the sound may be
interrupted when the monitor’s power is turned off.
• Use a cable on which the HDMI logo is indicated (a certified HDMI
product) for connection to the HDMI connector. Normal playback
may not be possible when using a cable other than one on which
the HDMI logo is indicated (a non-HDMI-certified product).
• If the monitor or DVD player does not support Deep Color, Deep
Color signal transfer is not possible.
• If the monitor or DVD player does not support xvYCC, xvYCC
signal transfer is not possible.
• If the monitor does not support “Auto Lipsync Correction”
function, this function will not work.
• The AVP-A1HDCI is compatible with the HDMI’s CEC (Consumer
Electronics Control) function. Please note the following.
It may not work depending on the device it is connected to and
its setup.
It does not operate with televisions or players that are not
compatible with HDMI’s CEC.
Connections