Filter
Top Products
13
Front & Rear Panels—Continued
REMOTE CONTROL
This (Remote Interactive) jack can be con-
nected to the jack on another -capable
Onkyo component for remote and system control.
To use , you must make an analog audio connec-
tion (RCA) between the AV receiver and the other
component, even if they are connected digitally.
RS232
PHONO IN
This audio input is for connecting a turntable.
COMPONENT VIDEO IN 1, 2, and 3
These RCA component video inputs are for con-
necting components with a component video out-
put, such as a DVD player, DVD recorder, or DVR
(digital video recorder). They’re assignable, which
means you can assign each one to an input selector
to suit your setup. See “Component Video Setup”
on page 58.
COMPONENT VIDEO MONITOR OUT
This RCA component video output is for connect-
ing a TV or projector with a component video input.
HDMI IN 1–4, OUT MAIN, and OUT SUB
HDMI (High Definition Multimedia Interface) con-
nections carry digital audio and digital video.
The HDMI inputs are for connecting components
with an HDMI output, such as a DVD player, DVD
recorder, or DVR (digital video recorder). They’re
assignable, which means you can assign each one to
an input selector to suit your setup. See “Video
Input Setup” on page 56.
The HDMI outputs are for connecting a TV or pro-
jector with an HDMI input.
SIRIUS antenna (on North American model)
This jack is for connecting a SIRIUS digital
antenna, sold separately (see the separate SIRIUS
instructions).
XM antenna (on North American model)
This jack is for connecting an XM Mini-Tuner and
Home Dock, sold separately (see the separate XM
instructions).
MONITOR OUT
The S-Video or composite video jack should be
connected to a video input on your TV or projector.
AM ANTENNA (not North American model)
These push terminals are for connecting an AM
antenna.
ZONE 2 OUT
This composite video output can be connected to a
video input on a TV in Zone 2.
FM ANTENNA (not North American model)
This jack is for connecting an FM antenna.
IR IN/OUT
A commercially available IR receiver can be con-
nected to the IR IN jack, allowing you to control the
AV receiver while you’re in Zone 2, or control it
when it’s out of sight, for example, installed in a
cabinet.
A commercially available IR emitter can be con-
nected to the IR OUT jack to pass IR (infrared)
remote control signals through to other components.
ETHERNET port (TX-NR906 only)
This port is for connecting the AV receiver to your
Ethernet network (e.g., router or switch) for playing
music files on a networked computer or media
server, or for listening to Internet radio.
12V TRIGGER OUT ZONE 2
This output can be connected to the 12-volt trigger
input on a component in Zone 2. When Zone 2 is
turned on, a 12-volt trigger signal is output.
AM and FM ANTENNA (HD Radio reception)
(on North American model)
The AM push terminals are for connecting an AM
antenna. The FM jack is for connecting an FM
antenna.
AC INLET
The supplied power cord is connected here. The
other end of the power cord should be connected to
a suitable wall outlet.
DIGITAL COAXIAL IN 1, 2, and 3
These coaxial digital audio inputs are for connect-
ing components with a coaxial digital audio output,
such as a CD player or DVD player. They’re assign-
able, which means you can assign each one to an
input selector to suit your setup. See “Digital Audio
Input Setup” on page 59.
DIGITAL OPTICAL IN 1, 2, and OUT
These optical digital audio inputs are for connecting
components with an optical digital audio output,
such as a CD player or DVD player. They’re assign-
able, which means you can assign each one to an
input selector to suit your setup. See “Digital Audio
Input Setup” on page 59.
The optical digital audio output is for connecting a
digital recorder with an optical digital input, such as
a CD recorder.
GND screw
This screw is for connecting a turntable’s ground
wire.
CD IN
This analog audio input is for connecting a CD
player’s analog audio output.