Onkyo NR906 Stereo System User Manual


 
95
Advanced Setup—Continued
This section explains items on the “Speaker Setup”
menu.
Some of the speaker settings are set automatically by the
Automatic Speaker Setup function (see page 64).
Speaker Settings
See “Speaker Settings” on page 61.
Speaker Configuration
With the Speaker Configuration settings, you can specify
which speakers are connected and a crossover frequency,
distance, and level for each speaker.
You can choose which of the speakers you want to use
with the Speakers A and Speakers B configurations, and
set the crossover frequencies, distances, and levels of the
front Speakers A and front Speakers B independently.
The other speakers (i.e., subwoofer, center, surround,
and surround back) use the same crossover frequencies,
distances, and levels for Speakers A and Speakers B.
The following crossover frequencies can be specified:
Full Band, 40 Hz, 50 Hz, 60 Hz, 70 Hz, 80 Hz (THX),
90 Hz, 100 Hz, 110 Hz, 120 Hz, 130 Hz, 150 Hz, or
200 Hz.
Specify Full Band for speakers that can output low-fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify
a crossover frequency. Sounds below the crossover fre-
quency will then be output by the subwoofer instead of
the speaker. Refer to your speakers’ manuals to deter-
mine the optimum crossover frequencies.
If you’re using THX-certified speakers, specify
80 Hz (THX) for all speakers.
Speaker Setup
INPUT SELECTOR
LISTENING MODE
DISPLAY MUTING
G
U
I
D
E
E
X
I
T
PREV
CH
DIMMER
CDR/MD/DOCK
SAT
TAPE/AMP
SLEEP
MACRO
REMOTE MODE
SUBTITLE
AUDIO
REPEAT
PLAY MODE
--
/
---
10 11 12
PLAYLIST
RANDOMREC
ENTER
SURR
DIRECT
THX
PURE A
STEREO
ALL ST
T
O
P
M
E
N
U
M
E
N
U
VOL
CH
DISC
ALBUM
TV
VCR
CABLE
NET/USB
DVD
RECEIVER
CD
123
ZONE
3
ZONE
2
+
-
S
E
T
U
P
R
E
T
U
R
N
SP A SP B
1, 5
1
2-4
1*
*TX-NR906 only
These settings are set automatically by the Automatic
Speaker Setup function (see page 64).
1
Press the [RECEIVER] REMOTE
MODE button, and then use the
remote controller’s [SP A] or
[SP B] button to select Speakers
A or Speakers B, respectively
(TX-NR906 only).
Note:
Speakers B cannot be selected if
“Speaker Type: Front(Speaker B)” is
set to “Not Use”.
TX-SR876 continue with step 2 after
press the [RECEIVER] REMOTE
MODE button.
2
Press the [SETUP] button.
The main menu appears onscreen.
3
Use the Up and Down [ ]/[ ] but-
tons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
4
Use the Up and Down [ ]/[ ] but-
tons to select “2. Speaker Con-
fig”, and then press [ENTER].
The “Speaker Config” screen appears.
2. Speaker Setup
1. Speaker Settings
2. Speaker Config
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
MOVE ENTER RETURN
ENTER
RETURN
EXIT
SETUP
RETURN
RETURN
EXIT
SETUP
MOVE VALU E
2–2. Speaker Config
Subwoofer
Front
Center
Surround
SurrBack
SurrBack Ch
LPF of LFE
DoubleBass
Yes
Full Band
100Hz
100Hz
100Hz
2ch
120Hz
On
Speaker A