Filter
Top Products
Graphical user interface (GUI) menu
85 En
Advanced
Operation
• If you set “Front Presence” to “None”, you cannot activate the CINEMA DSP HD³
mode (see page 60).
• “Dialogue Lift” is available when “Front Presence” is set to “Yes” and headphones
are not connected.
Rear Presence (Rear presence speakers)
Use this feature if you want to use the rear presence speakers
connected to this unit.
Subwoofer (Subwoofer)
Configuration (Subwoofer configuration)
Use this feature to select the configuration of the subwoofers
(see page 25).
y
If your subwoofer can adjust the output volume and the crossover frequency, set
the volume to about half way (or slightly less) and set the crossover frequency to
the maximum.
Phase (Subwoofer phase)
Use this feature to switch the phase of your subwoofers if bass
sounds are lacking or unclear.
Bass Out (Bass out)
Use this feature to select the speakers that output the LFE (low-
frequency effect) and the low-frequency signals.
THX Ltd. recommends that “Bass Out” to “SWFR”.
LFE signals output
Low-frequency signals output
*1 Output(s) the low-frequency signals of the front channels and other
speakers set to “Small”.
*2 Always output the low-frequency signals of the front channels.
*3 Output the low-frequency signals if the speakers are set to “Large”.
*4 Outputs the low-frequency signals of the speakers set to “Small” or
“None”.
■ Speaker Distance (Speaker distance)
Use this feature to manually adjust the distance of each speaker and the
delay applied to the respective channel. Ideally, each speaker should be
the same distance from the main listening position. However, this is not
possible in most home situations. Thus, a certain amount of delay must
be applied to the sound from each speaker so that all sounds will arrive
at the listening position at the same time.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Initial setting: 3.00 m (10.0 ft)
Control step: 0.05 m (0.2 ft)
y
If your subwoofer can adjust the output volume and the crossover frequency, set the
volume to about half way (or slightly less) and set the crossover frequency to the
maximum.
• The available speaker channels differ depending on the setting of the speakers.
• If you are only using one surround back speaker, connect it to the SUR.BACK
SINGLE jack, and adjust the distance in “Surround Back L”.
Unit (Unit)
Selects the unit for displaying the values of “Speaker Distance”
parameter.
Notes
Choice Descriptions
Yes
Select this setting when you use the rear presence
speakers.
None
Select this setting when you do not use the rear presence
speakers.
Choice Descriptions
Front & Rear
Select this setting when you place the subwoofers to
the front and rear of the listening room.
Stereo
Select this setting when you place the subwoofers to
the left and right of the listening room.
Monaural
Select this setting when you use a single subwoofer.
None
Select this setting when you do not use a subwoofer.
Choice Functions
Normal
Does not change the phase of your subwoofers.
L Reverse
Sets the phase of the left (or front) subwoofer to
reverse.
R Reverse
Sets the phase of the right (or rear) subwoofer to
reverse.
L&R Reverse
Sets the phase of the both subwoofers to reverse.
Choice
Subwoofers and speakers
Subwoofers
Front
speakers
Other
speakers
Front &
SWFR
Output No output No output
SWFR
Output No output No output
Front
No output Output No output
Choice
Subwoofers and speakers
Subwoofers
Front
speakers
Other
speakers
Front &
SWFR
*1 *2 *3
SWFR
*4 *3 *3
Front
No output *1 *3
Speaker Distance Adjusted speaker
Front L
Front left speaker
Front R
Front right speaker
Center
Center speaker
Surround L
Surround left speaker
Surround R
Surround right speaker
Surround Back L
Surround back left speaker
Surround Back R
Surround back right speaker
Front Presence L
Front presence left speaker
Front Presence R
Front presence right speaker
Rear Presence L
Rear presence left speaker
Rear Presence R
Rear presence right speaker
Subwoofer L
Subwoofer left
Subwoofer R
Subwoofer right
Notes
Choice Functions
Meter (m)
Adjusts speaker distances in meters.
Feet (ft)
Adjusts speaker distances in feet.