Filter
Top Products
Remote control features
105 En
Advanced
Operation
1 Press GSETUP on the remote control using a
ballpoint pen or similar object.
The remote control enters the setup menu. “SETUP” appears in
the display window (4) on the remote control.
2 Press 9k / n repeatedly to select “P-SET” and then
press 9ENTER.
The remote control enters the preset mode. “P-SET” and name
of the currently selected control area appears in the display
window (4) alternately.
3 Set the operation mode selector to GSOURCE and
then press an input selector button or (3) or
5SELECT l / h repeatedly to select the control
area you want to customize.
“P-SET” and name of the selected control area appears in the
display window (4) alternately.
y
If you want to select “TV”, set the operation mode selector to FTV.
4 Press 9ENTER.
The five-digit code set for the selected control area appears in
the display window (4).
“00000” appears in the display window (4) if no code has been set.
5 Press the numeric buttons (B) to enter the
five-digit remote control code for the component you
want to use.
For a complete list of available remote control codes, refer to
“List of remote control codes” at the end of this manual.
y
You can also enter the desired number by pressing 9 k / n / l / h repeatedly.
6 Press 9ENTER to set the number.
“OK” appears in the display window (4) if setting was
successful.
“NG” appears in the display window (4) if the setting was
unsuccessful. In this case, start over from step 3.
y
If you continuously want to set up another code for another control area, repeat
steps 3 through 6.
7 Press
G
SETUP again to exit from the setup mode.
8 Press
A
p or 2AV POWER to confirm whether you
can control your component using the remote
control.
y
If operation is not possible and the manufacturer of your component has more than one
code, try each of them until you find the correct one.
• “ERROR” appears in the display window (4) on the remote control if you press a
button not indicated in the respective step, or when you press more than one button
simultaneously.
• The supplied remote control does not contain all possible codes for commercially
available audio and video components (including Yamaha components). If operation
is not possible with any of the remote control codes, program the new remote control
function using the learning feature (see “Programming codes from other remote
controls (LEARN)” on page 105) or use the remote control supplied with the
component.
• Functions programmed using the learning mode take priority over remote control
code functions.
• If you set “00012” as the remote control code of the selected control area, you can
operate the currently selected internal source (DOCK, or NET/USB).
You can program remote control codes from other remote controls.
Use the learning feature if you want to program functions not
included in the basic operations covered by the remote control
codes, or an appropriate remote control code is not available. You
can program the function of other remote control to the buttons in
the highlighted areas in the following illustration. The buttons can
be programmed independently for each control area.
• The remote control transmits infrared rays. If the other remote control also uses
infrared rays, this remote control can learn most of its functions. However, you may
not be able to program some special signals or extremely long transmissions. Refer to
the operating instructions for the other remote control.
• You cannot program the desired remote control code even if you select the buttons in
the highlighted area in the above illustration depending on the selected control area
and the assigned library.
1 Set the operation mode selector to FSOURCE and
then press an input selector button or (3) to select
the desired control area.
The name of the control area you want to customize appears in
the display window (4) on the remote control.
y
• You can also select the desired control area by pressing 5SELECT l / h
repeatedly.
• If you want to select “TV”, set the operation mode selector to FTV.
Make sure that the operation mode selector is set to
F
SOURCE or FTV. When
you set the operation mode selector to FAMP and program a remote control
codes from other remote controls, the programmed key cannot operate the
amplifier function of this unit.
2 Press GSETUP using a ballpoint pen or similar
object.
“SETUP” appears in the display window (4).
Note
P-SET DVD
04306
Notes
Programming codes from other remote
controls (LEARN)
Notes
Note
AMP
TV
SOURCE
SELECT
SETUP ID
MACRO
DVD CD
V-A UXMULTI
AVTV
PHONO
CD-R
POWER
STANDBY
POWERPOWER
DTV DVR VCR
DOCK
TUNER
BD
HD DVD
MD
TAP E
CBL
SAT
NET
USB
4
3
SYSTEM
MEMORY
VOLUME
REC
SRCH MODELEVEL
BAND
MENUTITLE
CLASSICAL 1 CLASSICAL 2 LIVE/CLUB ENTERTAIN
MEMORY
PC/MCX
RETURN DISPLAY
PRESET/CH
ENTER
A-E
MUTE
2
1
NET RADIO
USB
MOVIE STEREO SUR. DECODE
EXTD SUR.
ENHANCER
THX STRAIGHT PURE DIRECT
PARTY SLEEP HDMI OUT AUDIO SEL
TV VOL TV CH TV
3D DSP
1234
5678
ENT
MUTE AUDIO
INPUT
90
10
Set to
SOURCE