Filter
Top Products
92
4-6 AUDIO Menu
Chapter 4 Menu Settings
number on the tape.
In this case, if SDOUT EXCHNG is set to “dis”, the
[F5]
button is also highlighted in orange.
•The
[F4] button in the AUDIO menu is highlighted in
orange if even one of the ANALOG audio output
channels does not match the corresponding track number
on the tape.
•The
[F5] button in the AUDIO menu is highlighted in
orange if even one of the SD SDI audio output channels
does not match the corresponding track number on the
tape.
4-6-1 Selecting the Audio Input
Signal (AUDIO IN)
To select the audio input signal for CH1 to CH12, use the
following procedure.
CH1 to CH12 can be selected for HDCAM-SR, and CH1
to CH4 can be selected for HDCAM.
1
Press the [F1] (AUDIO IN) button.
The AUDIO INPUT menu appears, together with an
audio input selection window.
2
Select the audio input signal for each channel.
SDI: audio signal input from the HD SDI INPUT A/B
connector
AES/EBU: audio signal input from the DIGITAL I/O
(AES/EBU) INPUT connector
3
Press the [F10] (EXIT) button.
This returns to the AUDIO menu screen.
To make settings for individual channels with the
F buttons
By pressing any of the [F1] (A-IN CH1) to [F8] (A-IN
CH8) buttons in the AUDIO INPUT menu, and the [F1]
(A-IN CH9) to [F4] (A-IN CH12) buttons in the
ALT+AUDIO screen obtained by pressing the ALT
button, you can select the type of input signal for each
channel.
To make input signal selections for individual
channels with the numeric buttons
1
Press the cursor T or t button, to align the cursor
with the channel for which you want to make the
selection.
2
Press the cursor R or r button, to select the signal.
To return to the default settings
Press the cursor center button. The cursor item returns to
the default.
To select the same input signal simultaneously
on all twelve channels
Press the [F9] (A-IN ALL) button to change the input
signal simultaneously on all twelve channels.
You can also make this setting using the VTR SETUP
menu item 830 “AUDIO INPUT SELECT”.
4-6-2 Digital Audio Output Signal
Source Track Selection (DIGOUT
EXCHNG)
To make the source track selection for the digital audio
output signal (audio multiplexed with HD SDI and SD SDI
(1 to 8 channels), and AES/EBU audio output are targeted)
on each of channels 1 to 12, use the following procedure.
Note that when [F9] (SDOUT EXCHNG) in the SDOUT
menu is set to “ena”, SD SDI source track selection
follows the settings of the SDOUT menu.
1
Press the [F3] (DIGOUT EXCHNG) button.
The DIGOUT menu appears, together with a source
track selection window for the digital audio output
signals.
2
Carry out the source track selection for the digital
audio output signal on each channel.
TR1 to TR12: Select the audio signals recorded on
tracks 1 to 12.
3
Press the [F10] (EXIT) button.
A-IN
CH1
AES/EB
A-IN
CH2
AES/EB
A-IN
CH3
SDI
A-IN
CH4
SDI
A-IN
CH5
SDI
A-IN
CH7
SDI
A-IN
CH8
SDI
A-IN
ALL
.....
EXITA-IN
CH6
SDI
AUDIO INPUT SELECT
CH1
A/E
CH2
A/E
CH3
SDI
CH4
SDI
CH5
SDI
CH6
SDI
CH7
SDI
CH8
SDI
CH9
SDI
CH10
SDI
CH11
SDI
CH12
SDI
DIGOUT
CH1
TR1
DIGOUT
CH2
TR2
DIGOUT
CH3
TR3
DIGOUT
CH4
TR4
DIGOUT
CH5
TR5
DIGOUT
CH7
TR7
DIGOUT
CH8
TR8
EXITDIGOUT
CH6
TR6
AUDIO OUTPUT EXCHANGE
CH1
TR1
CH2
TR2
CH3
TR3
CH4
TR4
CH5
TR5
CH6
TR6
CH7
TR7
CH8
TR8
CH9
TR9
CH10
TR10
CH11
TR11
CH12
TR12