Filter
Top Products
47
(Continued)
After finishing playback on an external unit:
The unit will automatically enter the recording stand-by mode.
Press the MD H button to cancel this mode.
I Pressing the MD H button allows the unit to record the TOC. When
performing other operations at the same time, perform them only after
this is cleared from the display.
Space-cut function:
If there is silence lasting 4 seconds or longer in the playback
signal during a synchro recording, recording will stop automati-
cally and the unit will enter the recording stand-by mode.
Then, when playback resumes, recording will automatically
restart.
(A space of 4 seconds is placed between tracks.)
I If there is noise between tracks, the synchro recording or the space-
cut function may not work properly. If this happens, record manually.
I When you need to record tracks or audio that include very weak
sounds lasting 4 seconds or more, manual recording is recom-
mended.
0dB
2
3
4
5
6
W - WW
-12
WWW
-4
WWWW
0
W> W
R
L
MDWWWW 1WW
WW 0:00WWWWWY
AUX1TWWWWWWA. MARKWONW
W-
-12
WWW
-4
WWWW
0
W> W
R
L
W -
-12
WWW
-4
WWWW
0
W> W
AUX1TWWWWWWWWWWWWWWWW
W - WW
-12
WWW
-4
WWWW
0
W> W
R
L
MDWWWW 1WW
WW 0:00WWWWWY
AUX1TWWWWWW A. MARKWONW
W- WW
-12
WWW
-4
WWWW
0
W> W
R
L
MDWWWW 1WW
WW 0:00WWWWWY
AUX1TWWWWWW A. MARKWONW
W- WW
-12
WWW
-4
WWWW
0
W> W
R
L
MDWWWW 1WW
WW 0:02WWWWWY
AUX1TWWWWWW A. MARKWONW
HH
HH
H Manual recording
1 Load a recordable MiniDisc.
2 Press the AUX button to select the auxiliary input.
I Select the input that corresponds to the terminals where the external
unit you want to record from is connected.
I Each time the button is pressed, the display will change as follows:
AUX1 AUX2 AUX OPT. AUX COAX PHONO
3 Press the REC button.
I When a CD is recorded from a digital source, "AUTO MARK" will not
appear.
To turn off the auto mark function:
I Press the AUTO MARK button on the remote control.
4 Start playback on the external unit.
I To record analog signals, perform steps 5 - 6.
I To record digital signals, perform step 6.
5 Adjust the recording level using the INPUT LEVEL control.
I The maximum level should not exceed 0 dB.
6 Press the MD 06 button.
HH
HH
H Track numbers
Recording CDs from a digital source:
Track numbers are automatically created to mark the beginning
of each track in the signal being recorded.
I When making digital recordings from using a CD player as the source,
track numbers may not be created automatically, depending on the
CD player used.
Other considerations:
When there is a period of silence of 1.5 seconds or longer in the
playback signal, a track number will be automatically created.
If there is no silence, tracks will be recorded as one track.
I If there is a lot of noise in the playback signal, track numbers may not
be created.
I Recordings can be made without using the auto mark function.
MD
MD
AUX
INPUT LEVEL
REC
AUX
REC
38-58 98.6.23, 10:34 AM47